From 63de3e307ee680676d3bb9870200f5200149a952 Mon Sep 17 00:00:00 2001 From: Dorian Stoll Date: Sun, 11 Dec 2022 12:03:38 +0100 Subject: [PATCH] iommu: intel: Disable source id verification for ITHC Signed-off-by: Dorian Stoll Patchset: ithc --- drivers/iommu/intel/irq_remapping.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/drivers/iommu/intel/irq_remapping.c b/drivers/iommu/intel/irq_remapping.c index 3bc2a03cceca..e4c95c0a87f9 100644 --- a/drivers/iommu/intel/irq_remapping.c +++ b/drivers/iommu/intel/irq_remapping.c @@ -380,6 +380,22 @@ static int set_msi_sid(struct irte *irte, struct pci_dev *dev) data.busmatch_count = 0; pci_for_each_dma_alias(dev, set_msi_sid_cb, &data); + /* + * The Intel Touch Host Controller is at 00:10.6, but for some reason + * the MSI interrupts have request id 01:05.0. + * Disable id verification to work around this. + * FIXME Find proper fix or turn this into a quirk. + */ + if (dev->vendor == PCI_VENDOR_ID_INTEL && (dev->class >> 8) == PCI_CLASS_INPUT_PEN) { + switch(dev->device) { + case 0x98d0: case 0x98d1: // LKF + case 0xa0d0: case 0xa0d1: // TGL LP + case 0x43d0: case 0x43d1: // TGL H + set_irte_sid(irte, SVT_NO_VERIFY, SQ_ALL_16, 0); + return 0; + } + } + /* * DMA alias provides us with a PCI device and alias. The only case * where the it will return an alias on a different bus than the -- 2.51.0 From 1a6a07daa136e37917ca622211c734a0d173deca Mon Sep 17 00:00:00 2001 From: quo Date: Sun, 11 Dec 2022 12:10:54 +0100 Subject: [PATCH] hid: Add support for Intel Touch Host Controller Based on quo/ithc-linux@34539af4726d. Signed-off-by: Maximilian Stoll Patchset: ithc --- drivers/hid/Kconfig | 2 + drivers/hid/Makefile | 1 + drivers/hid/ithc/Kbuild | 6 + drivers/hid/ithc/Kconfig | 12 + drivers/hid/ithc/ithc-debug.c | 149 ++++++++ drivers/hid/ithc/ithc-debug.h | 7 + drivers/hid/ithc/ithc-dma.c | 312 ++++++++++++++++ drivers/hid/ithc/ithc-dma.h | 47 +++ drivers/hid/ithc/ithc-hid.c | 207 +++++++++++ drivers/hid/ithc/ithc-hid.h | 32 ++ drivers/hid/ithc/ithc-legacy.c | 254 +++++++++++++ drivers/hid/ithc/ithc-legacy.h | 8 + drivers/hid/ithc/ithc-main.c | 438 ++++++++++++++++++++++ drivers/hid/ithc/ithc-quickspi.c | 607 +++++++++++++++++++++++++++++++ drivers/hid/ithc/ithc-quickspi.h | 39 ++ drivers/hid/ithc/ithc-regs.c | 154 ++++++++ drivers/hid/ithc/ithc-regs.h | 211 +++++++++++ drivers/hid/ithc/ithc.h | 89 +++++ 18 files changed, 2575 insertions(+) create mode 100644 drivers/hid/ithc/Kbuild create mode 100644 drivers/hid/ithc/Kconfig create mode 100644 drivers/hid/ithc/ithc-debug.c create mode 100644 drivers/hid/ithc/ithc-debug.h create mode 100644 drivers/hid/ithc/ithc-dma.c create mode 100644 drivers/hid/ithc/ithc-dma.h create mode 100644 drivers/hid/ithc/ithc-hid.c create mode 100644 drivers/hid/ithc/ithc-hid.h create mode 100644 drivers/hid/ithc/ithc-legacy.c create mode 100644 drivers/hid/ithc/ithc-legacy.h create mode 100644 drivers/hid/ithc/ithc-main.c create mode 100644 drivers/hid/ithc/ithc-quickspi.c create mode 100644 drivers/hid/ithc/ithc-quickspi.h create mode 100644 drivers/hid/ithc/ithc-regs.c create mode 100644 drivers/hid/ithc/ithc-regs.h create mode 100644 drivers/hid/ithc/ithc.h diff --git a/drivers/hid/Kconfig b/drivers/hid/Kconfig index ded8868dcfea..d6bc87be4854 100644 --- a/drivers/hid/Kconfig +++ b/drivers/hid/Kconfig @@ -1431,6 +1431,8 @@ source "drivers/hid/intel-thc-hid/Kconfig" source "drivers/hid/ipts/Kconfig" +source "drivers/hid/ithc/Kconfig" + endif # HID # USB support may be used with HID disabled diff --git a/drivers/hid/Makefile b/drivers/hid/Makefile index 7ba7d26391e9..d939da7ac2e8 100644 --- a/drivers/hid/Makefile +++ b/drivers/hid/Makefile @@ -177,3 +177,4 @@ obj-$(CONFIG_SURFACE_HID_CORE) += surface-hid/ obj-$(CONFIG_INTEL_THC_HID) += intel-thc-hid/ obj-$(CONFIG_HID_IPTS) += ipts/ +obj-$(CONFIG_HID_ITHC) += ithc/ diff --git a/drivers/hid/ithc/Kbuild b/drivers/hid/ithc/Kbuild new file mode 100644 index 000000000000..4937ba131297 --- /dev/null +++ b/drivers/hid/ithc/Kbuild @@ -0,0 +1,6 @@ +obj-$(CONFIG_HID_ITHC) := ithc.o + +ithc-objs := ithc-main.o ithc-regs.o ithc-dma.o ithc-hid.o ithc-legacy.o ithc-quickspi.o ithc-debug.o + +ccflags-y := -std=gnu11 -Wno-declaration-after-statement + diff --git a/drivers/hid/ithc/Kconfig b/drivers/hid/ithc/Kconfig new file mode 100644 index 000000000000..ede713023609 --- /dev/null +++ b/drivers/hid/ithc/Kconfig @@ -0,0 +1,12 @@ +config HID_ITHC + tristate "Intel Touch Host Controller" + depends on PCI + depends on HID + help + Say Y here if your system has a touchscreen using Intels + Touch Host Controller (ITHC / IPTS) technology. + + If unsure say N. + + To compile this driver as a module, choose M here: the + module will be called ithc. diff --git a/drivers/hid/ithc/ithc-debug.c b/drivers/hid/ithc/ithc-debug.c new file mode 100644 index 000000000000..2d8c6afe9966 --- /dev/null +++ b/drivers/hid/ithc/ithc-debug.c @@ -0,0 +1,149 @@ +// SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause + +#include "ithc.h" + +void ithc_log_regs(struct ithc *ithc) +{ + if (!ithc->prev_regs) + return; + u32 __iomem *cur = (__iomem void *)ithc->regs; + u32 *prev = (void *)ithc->prev_regs; + for (int i = 1024; i < sizeof(*ithc->regs) / 4; i++) { + u32 x = readl(cur + i); + if (x != prev[i]) { + pci_info(ithc->pci, "reg %04x: %08x -> %08x\n", i * 4, prev[i], x); + prev[i] = x; + } + } +} + +static ssize_t ithc_debugfs_cmd_write(struct file *f, const char __user *buf, size_t len, + loff_t *offset) +{ + // Debug commands consist of a single letter followed by a list of numbers (decimal or + // hexadecimal, space-separated). + struct ithc *ithc = file_inode(f)->i_private; + char cmd[256]; + if (!ithc || !ithc->pci) + return -ENODEV; + if (!len) + return -EINVAL; + if (len >= sizeof(cmd)) + return -EINVAL; + if (copy_from_user(cmd, buf, len)) + return -EFAULT; + cmd[len] = 0; + if (cmd[len-1] == '\n') + cmd[len-1] = 0; + pci_info(ithc->pci, "debug command: %s\n", cmd); + + // Parse the list of arguments into a u32 array. + u32 n = 0; + const char *s = cmd + 1; + u32 a[32]; + while (*s && *s != '\n') { + if (n >= ARRAY_SIZE(a)) + return -EINVAL; + if (*s++ != ' ') + return -EINVAL; + char *e; + a[n++] = simple_strtoul(s, &e, 0); + if (e == s) + return -EINVAL; + s = e; + } + ithc_log_regs(ithc); + + // Execute the command. + switch (cmd[0]) { + case 'x': // reset + ithc_reset(ithc); + break; + case 'w': // write register: offset mask value + if (n != 3 || (a[0] & 3)) + return -EINVAL; + pci_info(ithc->pci, "debug write 0x%04x = 0x%08x (mask 0x%08x)\n", + a[0], a[2], a[1]); + bitsl(((__iomem u32 *)ithc->regs) + a[0] / 4, a[1], a[2]); + break; + case 'r': // read register: offset + if (n != 1 || (a[0] & 3)) + return -EINVAL; + pci_info(ithc->pci, "debug read 0x%04x = 0x%08x\n", a[0], + readl(((__iomem u32 *)ithc->regs) + a[0] / 4)); + break; + case 's': // spi command: cmd offset len data... + // read config: s 4 0 64 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + // set touch cfg: s 6 12 4 XX + if (n < 3 || a[2] > (n - 3) * 4) + return -EINVAL; + pci_info(ithc->pci, "debug spi command %u with %u bytes of data\n", a[0], a[2]); + if (!CHECK(ithc_spi_command, ithc, a[0], a[1], a[2], a + 3)) + for (u32 i = 0; i < (a[2] + 3) / 4; i++) + pci_info(ithc->pci, "resp %u = 0x%08x\n", i, a[3+i]); + break; + case 'd': // dma command: cmd len data... + // get report descriptor: d 7 8 0 0 + // enable multitouch: d 3 2 0x0105 + if (n < 1) + return -EINVAL; + pci_info(ithc->pci, "debug dma command with %u bytes of data\n", n * 4); + struct ithc_data data = { .type = ITHC_DATA_RAW, .size = n * 4, .data = a }; + if (ithc_dma_tx(ithc, &data)) + pci_err(ithc->pci, "dma tx failed\n"); + break; + default: + return -EINVAL; + } + ithc_log_regs(ithc); + return len; +} + +static struct dentry *dbg_dir; + +void __init ithc_debug_init_module(void) +{ + struct dentry *d = debugfs_create_dir(DEVNAME, NULL); + if (IS_ERR(d)) + pr_warn("failed to create debugfs dir (%li)\n", PTR_ERR(d)); + else + dbg_dir = d; +} + +void __exit ithc_debug_exit_module(void) +{ + debugfs_remove_recursive(dbg_dir); + dbg_dir = NULL; +} + +static const struct file_operations ithc_debugfops_cmd = { + .owner = THIS_MODULE, + .write = ithc_debugfs_cmd_write, +}; + +static void ithc_debugfs_devres_release(struct device *dev, void *res) +{ + struct dentry **dbgm = res; + debugfs_remove_recursive(*dbgm); +} + +int ithc_debug_init_device(struct ithc *ithc) +{ + if (!dbg_dir) + return -ENOENT; + struct dentry **dbgm = devres_alloc(ithc_debugfs_devres_release, sizeof(*dbgm), GFP_KERNEL); + if (!dbgm) + return -ENOMEM; + devres_add(&ithc->pci->dev, dbgm); + struct dentry *dbg = debugfs_create_dir(pci_name(ithc->pci), dbg_dir); + if (IS_ERR(dbg)) + return PTR_ERR(dbg); + *dbgm = dbg; + + struct dentry *cmd = debugfs_create_file("cmd", 0220, dbg, ithc, &ithc_debugfops_cmd); + if (IS_ERR(cmd)) + return PTR_ERR(cmd); + + return 0; +} + diff --git a/drivers/hid/ithc/ithc-debug.h b/drivers/hid/ithc/ithc-debug.h new file mode 100644 index 000000000000..38c53d916bdb --- /dev/null +++ b/drivers/hid/ithc/ithc-debug.h @@ -0,0 +1,7 @@ +/* SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause */ + +void ithc_debug_init_module(void); +void ithc_debug_exit_module(void); +int ithc_debug_init_device(struct ithc *ithc); +void ithc_log_regs(struct ithc *ithc); + diff --git a/drivers/hid/ithc/ithc-dma.c b/drivers/hid/ithc/ithc-dma.c new file mode 100644 index 000000000000..bf4eab33062b --- /dev/null +++ b/drivers/hid/ithc/ithc-dma.c @@ -0,0 +1,312 @@ +// SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause + +#include "ithc.h" + +// The THC uses tables of PRDs (physical region descriptors) to describe the TX and RX data buffers. +// Each PRD contains the DMA address and size of a block of DMA memory, and some status flags. +// This allows each data buffer to consist of multiple non-contiguous blocks of memory. + +static int ithc_dma_prd_alloc(struct ithc *ithc, struct ithc_dma_prd_buffer *p, + unsigned int num_buffers, unsigned int num_pages, enum dma_data_direction dir) +{ + p->num_pages = num_pages; + p->dir = dir; + // We allocate enough space to have one PRD per data buffer page, however if the data + // buffer pages happen to be contiguous, we can describe the buffer using fewer PRDs, so + // some will remain unused (which is fine). + p->size = round_up(num_buffers * num_pages * sizeof(struct ithc_phys_region_desc), PAGE_SIZE); + p->addr = dmam_alloc_coherent(&ithc->pci->dev, p->size, &p->dma_addr, GFP_KERNEL); + if (!p->addr) + return -ENOMEM; + if (p->dma_addr & (PAGE_SIZE - 1)) + return -EFAULT; + return 0; +} + +// Devres managed sg_table wrapper. +struct ithc_sg_table { + void *addr; + struct sg_table sgt; + enum dma_data_direction dir; +}; +static void ithc_dma_sgtable_free(struct sg_table *sgt) +{ + struct scatterlist *sg; + int i; + for_each_sgtable_sg(sgt, sg, i) { + struct page *p = sg_page(sg); + if (p) + __free_page(p); + } + sg_free_table(sgt); +} +static void ithc_dma_data_devres_release(struct device *dev, void *res) +{ + struct ithc_sg_table *sgt = res; + if (sgt->addr) + vunmap(sgt->addr); + dma_unmap_sgtable(dev, &sgt->sgt, sgt->dir, 0); + ithc_dma_sgtable_free(&sgt->sgt); +} + +static int ithc_dma_data_alloc(struct ithc *ithc, struct ithc_dma_prd_buffer *prds, + struct ithc_dma_data_buffer *b) +{ + // We don't use dma_alloc_coherent() for data buffers, because they don't have to be + // coherent (they are unidirectional) or contiguous (we can use one PRD per page). + // We could use dma_alloc_noncontiguous(), however this still always allocates a single + // DMA mapped segment, which is more restrictive than what we need. + // Instead we use an sg_table of individually allocated pages. + struct page *pages[16]; + if (prds->num_pages == 0 || prds->num_pages > ARRAY_SIZE(pages)) + return -EINVAL; + b->active_idx = -1; + struct ithc_sg_table *sgt = devres_alloc( + ithc_dma_data_devres_release, sizeof(*sgt), GFP_KERNEL); + if (!sgt) + return -ENOMEM; + sgt->dir = prds->dir; + + if (!sg_alloc_table(&sgt->sgt, prds->num_pages, GFP_KERNEL)) { + struct scatterlist *sg; + int i; + bool ok = true; + for_each_sgtable_sg(&sgt->sgt, sg, i) { + // NOTE: don't need __GFP_DMA for PCI DMA + struct page *p = pages[i] = alloc_page(GFP_KERNEL | __GFP_ZERO); + if (!p) { + ok = false; + break; + } + sg_set_page(sg, p, PAGE_SIZE, 0); + } + if (ok && !dma_map_sgtable(&ithc->pci->dev, &sgt->sgt, prds->dir, 0)) { + devres_add(&ithc->pci->dev, sgt); + b->sgt = &sgt->sgt; + b->addr = sgt->addr = vmap(pages, prds->num_pages, 0, PAGE_KERNEL); + if (!b->addr) + return -ENOMEM; + return 0; + } + ithc_dma_sgtable_free(&sgt->sgt); + } + devres_free(sgt); + return -ENOMEM; +} + +static int ithc_dma_data_buffer_put(struct ithc *ithc, struct ithc_dma_prd_buffer *prds, + struct ithc_dma_data_buffer *b, unsigned int idx) +{ + // Give a buffer to the THC. + struct ithc_phys_region_desc *prd = prds->addr; + prd += idx * prds->num_pages; + if (b->active_idx >= 0) { + pci_err(ithc->pci, "buffer already active\n"); + return -EINVAL; + } + b->active_idx = idx; + if (prds->dir == DMA_TO_DEVICE) { + // TX buffer: Caller should have already filled the data buffer, so just fill + // the PRD and flush. + // (TODO: Support multi-page TX buffers. So far no device seems to use or need + // these though.) + if (b->data_size > PAGE_SIZE) + return -EINVAL; + prd->addr = sg_dma_address(b->sgt->sgl) >> 10; + prd->size = b->data_size | PRD_FLAG_END; + flush_kernel_vmap_range(b->addr, b->data_size); + } else if (prds->dir == DMA_FROM_DEVICE) { + // RX buffer: Reset PRDs. + struct scatterlist *sg; + int i; + for_each_sgtable_dma_sg(b->sgt, sg, i) { + prd->addr = sg_dma_address(sg) >> 10; + prd->size = sg_dma_len(sg); + prd++; + } + prd[-1].size |= PRD_FLAG_END; + } + dma_wmb(); // for the prds + dma_sync_sgtable_for_device(&ithc->pci->dev, b->sgt, prds->dir); + return 0; +} + +static int ithc_dma_data_buffer_get(struct ithc *ithc, struct ithc_dma_prd_buffer *prds, + struct ithc_dma_data_buffer *b, unsigned int idx) +{ + // Take a buffer from the THC. + struct ithc_phys_region_desc *prd = prds->addr; + prd += idx * prds->num_pages; + // This is purely a sanity check. We don't strictly need the idx parameter for this + // function, because it should always be the same as active_idx, unless we have a bug. + if (b->active_idx != idx) { + pci_err(ithc->pci, "wrong buffer index\n"); + return -EINVAL; + } + b->active_idx = -1; + if (prds->dir == DMA_FROM_DEVICE) { + // RX buffer: Calculate actual received data size from PRDs. + dma_rmb(); // for the prds + b->data_size = 0; + struct scatterlist *sg; + int i; + for_each_sgtable_dma_sg(b->sgt, sg, i) { + unsigned int size = prd->size; + b->data_size += size & PRD_SIZE_MASK; + if (size & PRD_FLAG_END) + break; + if ((size & PRD_SIZE_MASK) != sg_dma_len(sg)) { + pci_err(ithc->pci, "truncated prd\n"); + break; + } + prd++; + } + invalidate_kernel_vmap_range(b->addr, b->data_size); + } + dma_sync_sgtable_for_cpu(&ithc->pci->dev, b->sgt, prds->dir); + return 0; +} + +int ithc_dma_rx_init(struct ithc *ithc, u8 channel) +{ + struct ithc_dma_rx *rx = &ithc->dma_rx[channel]; + mutex_init(&rx->mutex); + + // Allocate buffers. + unsigned int num_pages = (ithc->max_rx_size + PAGE_SIZE - 1) / PAGE_SIZE; + pci_dbg(ithc->pci, "allocating rx buffers: num = %u, size = %u, pages = %u\n", + NUM_RX_BUF, ithc->max_rx_size, num_pages); + CHECK_RET(ithc_dma_prd_alloc, ithc, &rx->prds, NUM_RX_BUF, num_pages, DMA_FROM_DEVICE); + for (unsigned int i = 0; i < NUM_RX_BUF; i++) + CHECK_RET(ithc_dma_data_alloc, ithc, &rx->prds, &rx->bufs[i]); + + // Init registers. + writeb(DMA_RX_CONTROL2_RESET, &ithc->regs->dma_rx[channel].control2); + lo_hi_writeq(rx->prds.dma_addr, &ithc->regs->dma_rx[channel].addr); + writeb(NUM_RX_BUF - 1, &ithc->regs->dma_rx[channel].num_bufs); + writeb(num_pages - 1, &ithc->regs->dma_rx[channel].num_prds); + u8 head = readb(&ithc->regs->dma_rx[channel].head); + if (head) { + pci_err(ithc->pci, "head is nonzero (%u)\n", head); + return -EIO; + } + + // Init buffers. + for (unsigned int i = 0; i < NUM_RX_BUF; i++) + CHECK_RET(ithc_dma_data_buffer_put, ithc, &rx->prds, &rx->bufs[i], i); + + writeb(head ^ DMA_RX_WRAP_FLAG, &ithc->regs->dma_rx[channel].tail); + return 0; +} + +void ithc_dma_rx_enable(struct ithc *ithc, u8 channel) +{ + bitsb_set(&ithc->regs->dma_rx[channel].control, + DMA_RX_CONTROL_ENABLE | DMA_RX_CONTROL_IRQ_ERROR | DMA_RX_CONTROL_IRQ_DATA); + CHECK(waitl, ithc, &ithc->regs->dma_rx[channel].status, + DMA_RX_STATUS_ENABLED, DMA_RX_STATUS_ENABLED); +} + +int ithc_dma_tx_init(struct ithc *ithc) +{ + struct ithc_dma_tx *tx = &ithc->dma_tx; + mutex_init(&tx->mutex); + + // Allocate buffers. + unsigned int num_pages = (ithc->max_tx_size + PAGE_SIZE - 1) / PAGE_SIZE; + pci_dbg(ithc->pci, "allocating tx buffers: size = %u, pages = %u\n", + ithc->max_tx_size, num_pages); + CHECK_RET(ithc_dma_prd_alloc, ithc, &tx->prds, 1, num_pages, DMA_TO_DEVICE); + CHECK_RET(ithc_dma_data_alloc, ithc, &tx->prds, &tx->buf); + + // Init registers. + lo_hi_writeq(tx->prds.dma_addr, &ithc->regs->dma_tx.addr); + writeb(num_pages - 1, &ithc->regs->dma_tx.num_prds); + + // Init buffers. + CHECK_RET(ithc_dma_data_buffer_put, ithc, &ithc->dma_tx.prds, &ithc->dma_tx.buf, 0); + return 0; +} + +static int ithc_dma_rx_unlocked(struct ithc *ithc, u8 channel) +{ + // Process all filled RX buffers from the ringbuffer. + struct ithc_dma_rx *rx = &ithc->dma_rx[channel]; + unsigned int n = rx->num_received; + u8 head_wrap = readb(&ithc->regs->dma_rx[channel].head); + while (1) { + u8 tail = n % NUM_RX_BUF; + u8 tail_wrap = tail | ((n / NUM_RX_BUF) & 1 ? 0 : DMA_RX_WRAP_FLAG); + writeb(tail_wrap, &ithc->regs->dma_rx[channel].tail); + // ringbuffer is full if tail_wrap == head_wrap + // ringbuffer is empty if tail_wrap == head_wrap ^ WRAP_FLAG + if (tail_wrap == (head_wrap ^ DMA_RX_WRAP_FLAG)) + return 0; + + // take the buffer that the device just filled + struct ithc_dma_data_buffer *b = &rx->bufs[n % NUM_RX_BUF]; + CHECK_RET(ithc_dma_data_buffer_get, ithc, &rx->prds, b, tail); + rx->num_received = ++n; + + // process data + struct ithc_data d; + if ((ithc->use_quickspi ? ithc_quickspi_decode_rx : ithc_legacy_decode_rx) + (ithc, b->addr, b->data_size, &d) < 0) { + pci_err(ithc->pci, "invalid dma rx data! channel %u, buffer %u, size %u: %*ph\n", + channel, tail, b->data_size, min((int)b->data_size, 64), b->addr); + print_hex_dump_debug(DEVNAME " data: ", DUMP_PREFIX_OFFSET, 32, 1, + b->addr, min(b->data_size, 0x400u), 0); + } else { + ithc_hid_process_data(ithc, &d); + } + + // give the buffer back to the device + CHECK_RET(ithc_dma_data_buffer_put, ithc, &rx->prds, b, tail); + } +} +int ithc_dma_rx(struct ithc *ithc, u8 channel) +{ + struct ithc_dma_rx *rx = &ithc->dma_rx[channel]; + mutex_lock(&rx->mutex); + int ret = ithc_dma_rx_unlocked(ithc, channel); + mutex_unlock(&rx->mutex); + return ret; +} + +static int ithc_dma_tx_unlocked(struct ithc *ithc, const struct ithc_data *data) +{ + // Send a single TX buffer to the THC. + pci_dbg(ithc->pci, "dma tx data type %u, size %u\n", data->type, data->size); + CHECK_RET(ithc_dma_data_buffer_get, ithc, &ithc->dma_tx.prds, &ithc->dma_tx.buf, 0); + + // Fill the TX buffer with header and data. + ssize_t sz; + if (data->type == ITHC_DATA_RAW) { + sz = min(data->size, ithc->max_tx_size); + memcpy(ithc->dma_tx.buf.addr, data->data, sz); + } else { + sz = (ithc->use_quickspi ? ithc_quickspi_encode_tx : ithc_legacy_encode_tx) + (ithc, data, ithc->dma_tx.buf.addr, ithc->max_tx_size); + } + ithc->dma_tx.buf.data_size = sz < 0 ? 0 : sz; + CHECK_RET(ithc_dma_data_buffer_put, ithc, &ithc->dma_tx.prds, &ithc->dma_tx.buf, 0); + if (sz < 0) { + pci_err(ithc->pci, "failed to encode tx data type %i, size %u, error %i\n", + data->type, data->size, (int)sz); + return -EINVAL; + } + + // Let the THC process the buffer. + bitsb_set(&ithc->regs->dma_tx.control, DMA_TX_CONTROL_SEND); + CHECK_RET(waitb, ithc, &ithc->regs->dma_tx.control, DMA_TX_CONTROL_SEND, 0); + writel(DMA_TX_STATUS_DONE, &ithc->regs->dma_tx.status); + return 0; +} +int ithc_dma_tx(struct ithc *ithc, const struct ithc_data *data) +{ + mutex_lock(&ithc->dma_tx.mutex); + int ret = ithc_dma_tx_unlocked(ithc, data); + mutex_unlock(&ithc->dma_tx.mutex); + return ret; +} + diff --git a/drivers/hid/ithc/ithc-dma.h b/drivers/hid/ithc/ithc-dma.h new file mode 100644 index 000000000000..1749a5819b3e --- /dev/null +++ b/drivers/hid/ithc/ithc-dma.h @@ -0,0 +1,47 @@ +/* SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause */ + +#define PRD_SIZE_MASK 0xffffff +#define PRD_FLAG_END 0x1000000 +#define PRD_FLAG_SUCCESS 0x2000000 +#define PRD_FLAG_ERROR 0x4000000 + +struct ithc_phys_region_desc { + u64 addr; // physical addr/1024 + u32 size; // num bytes, PRD_FLAG_END marks last prd for data split over multiple prds + u32 unused; +}; + +struct ithc_dma_prd_buffer { + void *addr; + dma_addr_t dma_addr; + u32 size; + u32 num_pages; // per data buffer + enum dma_data_direction dir; +}; + +struct ithc_dma_data_buffer { + void *addr; + struct sg_table *sgt; + int active_idx; + u32 data_size; +}; + +struct ithc_dma_tx { + struct mutex mutex; + struct ithc_dma_prd_buffer prds; + struct ithc_dma_data_buffer buf; +}; + +struct ithc_dma_rx { + struct mutex mutex; + u32 num_received; + struct ithc_dma_prd_buffer prds; + struct ithc_dma_data_buffer bufs[NUM_RX_BUF]; +}; + +int ithc_dma_rx_init(struct ithc *ithc, u8 channel); +void ithc_dma_rx_enable(struct ithc *ithc, u8 channel); +int ithc_dma_tx_init(struct ithc *ithc); +int ithc_dma_rx(struct ithc *ithc, u8 channel); +int ithc_dma_tx(struct ithc *ithc, const struct ithc_data *data); + diff --git a/drivers/hid/ithc/ithc-hid.c b/drivers/hid/ithc/ithc-hid.c new file mode 100644 index 000000000000..065646ab499e --- /dev/null +++ b/drivers/hid/ithc/ithc-hid.c @@ -0,0 +1,207 @@ +// SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause + +#include "ithc.h" + +static int ithc_hid_start(struct hid_device *hdev) { return 0; } +static void ithc_hid_stop(struct hid_device *hdev) { } +static int ithc_hid_open(struct hid_device *hdev) { return 0; } +static void ithc_hid_close(struct hid_device *hdev) { } + +static int ithc_hid_parse(struct hid_device *hdev) +{ + struct ithc *ithc = hdev->driver_data; + const struct ithc_data get_report_desc = { .type = ITHC_DATA_REPORT_DESCRIPTOR }; + WRITE_ONCE(ithc->hid.parse_done, false); + for (int retries = 0; ; retries++) { + ithc_log_regs(ithc); + CHECK_RET(ithc_dma_tx, ithc, &get_report_desc); + if (wait_event_timeout(ithc->hid.wait_parse, READ_ONCE(ithc->hid.parse_done), + msecs_to_jiffies(200))) { + ithc_log_regs(ithc); + return 0; + } + if (retries > 5) { + ithc_log_regs(ithc); + pci_err(ithc->pci, "failed to read report descriptor\n"); + return -ETIMEDOUT; + } + pci_warn(ithc->pci, "failed to read report descriptor, retrying\n"); + } +} + +static int ithc_hid_raw_request(struct hid_device *hdev, unsigned char reportnum, __u8 *buf, + size_t len, unsigned char rtype, int reqtype) +{ + struct ithc *ithc = hdev->driver_data; + if (!buf || !len) + return -EINVAL; + + struct ithc_data d = { .size = len, .data = buf }; + buf[0] = reportnum; + + if (rtype == HID_OUTPUT_REPORT && reqtype == HID_REQ_SET_REPORT) { + d.type = ITHC_DATA_OUTPUT_REPORT; + CHECK_RET(ithc_dma_tx, ithc, &d); + return 0; + } + + if (rtype == HID_FEATURE_REPORT && reqtype == HID_REQ_SET_REPORT) { + d.type = ITHC_DATA_SET_FEATURE; + CHECK_RET(ithc_dma_tx, ithc, &d); + return 0; + } + + if (rtype == HID_FEATURE_REPORT && reqtype == HID_REQ_GET_REPORT) { + d.type = ITHC_DATA_GET_FEATURE; + d.data = &reportnum; + d.size = 1; + + // Prepare for response. + mutex_lock(&ithc->hid.get_feature_mutex); + ithc->hid.get_feature_buf = buf; + ithc->hid.get_feature_size = len; + mutex_unlock(&ithc->hid.get_feature_mutex); + + // Transmit 'get feature' request. + int r = CHECK(ithc_dma_tx, ithc, &d); + if (!r) { + r = wait_event_interruptible_timeout(ithc->hid.wait_get_feature, + !ithc->hid.get_feature_buf, msecs_to_jiffies(1000)); + if (!r) + r = -ETIMEDOUT; + else if (r < 0) + r = -EINTR; + else + r = 0; + } + + // If everything went ok, the buffer has been filled with the response data. + // Return the response size. + mutex_lock(&ithc->hid.get_feature_mutex); + ithc->hid.get_feature_buf = NULL; + if (!r) + r = ithc->hid.get_feature_size; + mutex_unlock(&ithc->hid.get_feature_mutex); + return r; + } + + pci_err(ithc->pci, "unhandled hid request %i %i for report id %i\n", + rtype, reqtype, reportnum); + return -EINVAL; +} + +// FIXME hid_input_report()/hid_parse_report() currently don't take const buffers, so we have to +// cast away the const to avoid a compiler warning... +#define NOCONST(x) ((void *)x) + +void ithc_hid_process_data(struct ithc *ithc, struct ithc_data *d) +{ + WARN_ON(!ithc->hid.dev); + if (!ithc->hid.dev) + return; + + switch (d->type) { + + case ITHC_DATA_IGNORE: + return; + + case ITHC_DATA_ERROR: + CHECK(ithc_reset, ithc); + return; + + case ITHC_DATA_REPORT_DESCRIPTOR: + // Response to the report descriptor request sent by ithc_hid_parse(). + CHECK(hid_parse_report, ithc->hid.dev, NOCONST(d->data), d->size); + WRITE_ONCE(ithc->hid.parse_done, true); + wake_up(&ithc->hid.wait_parse); + return; + + case ITHC_DATA_INPUT_REPORT: + { + // Standard HID input report. + int r = hid_input_report(ithc->hid.dev, HID_INPUT_REPORT, NOCONST(d->data), d->size, 1); + if (r < 0) { + pci_warn(ithc->pci, "hid_input_report failed with %i (size %u, report ID 0x%02x)\n", + r, d->size, d->size ? *(u8 *)d->data : 0); + print_hex_dump_debug(DEVNAME " report: ", DUMP_PREFIX_OFFSET, 32, 1, + d->data, min(d->size, 0x400u), 0); + } + return; + } + + case ITHC_DATA_GET_FEATURE: + { + // Response to a 'get feature' request sent by ithc_hid_raw_request(). + bool done = false; + mutex_lock(&ithc->hid.get_feature_mutex); + if (ithc->hid.get_feature_buf) { + if (d->size < ithc->hid.get_feature_size) + ithc->hid.get_feature_size = d->size; + memcpy(ithc->hid.get_feature_buf, d->data, ithc->hid.get_feature_size); + ithc->hid.get_feature_buf = NULL; + done = true; + } + mutex_unlock(&ithc->hid.get_feature_mutex); + if (done) { + wake_up(&ithc->hid.wait_get_feature); + } else { + // Received data without a matching request, or the request already + // timed out. (XXX What's the correct thing to do here?) + CHECK(hid_input_report, ithc->hid.dev, HID_FEATURE_REPORT, + NOCONST(d->data), d->size, 1); + } + return; + } + + default: + pci_err(ithc->pci, "unhandled data type %i\n", d->type); + return; + } +} + +static struct hid_ll_driver ithc_ll_driver = { + .start = ithc_hid_start, + .stop = ithc_hid_stop, + .open = ithc_hid_open, + .close = ithc_hid_close, + .parse = ithc_hid_parse, + .raw_request = ithc_hid_raw_request, +}; + +static void ithc_hid_devres_release(struct device *dev, void *res) +{ + struct hid_device **hidm = res; + if (*hidm) + hid_destroy_device(*hidm); +} + +int ithc_hid_init(struct ithc *ithc) +{ + struct hid_device **hidm = devres_alloc(ithc_hid_devres_release, sizeof(*hidm), GFP_KERNEL); + if (!hidm) + return -ENOMEM; + devres_add(&ithc->pci->dev, hidm); + struct hid_device *hid = hid_allocate_device(); + if (IS_ERR(hid)) + return PTR_ERR(hid); + *hidm = hid; + + strscpy(hid->name, DEVFULLNAME, sizeof(hid->name)); + strscpy(hid->phys, ithc->phys, sizeof(hid->phys)); + hid->ll_driver = &ithc_ll_driver; + hid->bus = BUS_PCI; + hid->vendor = ithc->vendor_id; + hid->product = ithc->product_id; + hid->version = 0x100; + hid->dev.parent = &ithc->pci->dev; + hid->driver_data = ithc; + + ithc->hid.dev = hid; + + init_waitqueue_head(&ithc->hid.wait_parse); + init_waitqueue_head(&ithc->hid.wait_get_feature); + mutex_init(&ithc->hid.get_feature_mutex); + + return 0; +} + diff --git a/drivers/hid/ithc/ithc-hid.h b/drivers/hid/ithc/ithc-hid.h new file mode 100644 index 000000000000..599eb912c8c8 --- /dev/null +++ b/drivers/hid/ithc/ithc-hid.h @@ -0,0 +1,32 @@ +/* SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause */ + +enum ithc_data_type { + ITHC_DATA_IGNORE, + ITHC_DATA_RAW, + ITHC_DATA_ERROR, + ITHC_DATA_REPORT_DESCRIPTOR, + ITHC_DATA_INPUT_REPORT, + ITHC_DATA_OUTPUT_REPORT, + ITHC_DATA_GET_FEATURE, + ITHC_DATA_SET_FEATURE, +}; + +struct ithc_data { + enum ithc_data_type type; + u32 size; + const void *data; +}; + +struct ithc_hid { + struct hid_device *dev; + bool parse_done; + wait_queue_head_t wait_parse; + wait_queue_head_t wait_get_feature; + struct mutex get_feature_mutex; + void *get_feature_buf; + size_t get_feature_size; +}; + +int ithc_hid_init(struct ithc *ithc); +void ithc_hid_process_data(struct ithc *ithc, struct ithc_data *d); + diff --git a/drivers/hid/ithc/ithc-legacy.c b/drivers/hid/ithc/ithc-legacy.c new file mode 100644 index 000000000000..8883987fb352 --- /dev/null +++ b/drivers/hid/ithc/ithc-legacy.c @@ -0,0 +1,254 @@ +// SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause + +#include "ithc.h" + +#define DEVCFG_DMA_RX_SIZE(x) ((((x) & 0x3fff) + 1) << 6) +#define DEVCFG_DMA_TX_SIZE(x) (((((x) >> 14) & 0x3ff) + 1) << 6) + +#define DEVCFG_TOUCH_MASK 0x3f +#define DEVCFG_TOUCH_ENABLE BIT(0) +#define DEVCFG_TOUCH_PROP_DATA_ENABLE BIT(1) +#define DEVCFG_TOUCH_HID_REPORT_ENABLE BIT(2) +#define DEVCFG_TOUCH_POWER_STATE(x) (((x) & 7) << 3) +#define DEVCFG_TOUCH_UNKNOWN_6 BIT(6) + +#define DEVCFG_DEVICE_ID_TIC 0x43495424 // "$TIC" + +#define DEVCFG_SPI_CLKDIV(x) (((x) >> 1) & 7) +#define DEVCFG_SPI_CLKDIV_8 BIT(4) +#define DEVCFG_SPI_SUPPORTS_SINGLE BIT(5) +#define DEVCFG_SPI_SUPPORTS_DUAL BIT(6) +#define DEVCFG_SPI_SUPPORTS_QUAD BIT(7) +#define DEVCFG_SPI_MAX_TOUCH_POINTS(x) (((x) >> 8) & 0x3f) +#define DEVCFG_SPI_MIN_RESET_TIME(x) (((x) >> 16) & 0xf) +#define DEVCFG_SPI_NEEDS_HEARTBEAT BIT(20) // TODO implement heartbeat +#define DEVCFG_SPI_HEARTBEAT_INTERVAL(x) (((x) >> 21) & 7) +#define DEVCFG_SPI_UNKNOWN_25 BIT(25) +#define DEVCFG_SPI_UNKNOWN_26 BIT(26) +#define DEVCFG_SPI_UNKNOWN_27 BIT(27) +#define DEVCFG_SPI_DELAY(x) (((x) >> 28) & 7) // TODO use this +#define DEVCFG_SPI_USE_EXT_READ_CFG BIT(31) // TODO use this? + +struct ithc_device_config { // (Example values are from an SP7+.) + u32 irq_cause; // 00 = 0xe0000402 (0xe0000401 after DMA_RX_CODE_RESET) + u32 error; // 04 = 0x00000000 + u32 dma_buf_sizes; // 08 = 0x000a00ff + u32 touch_cfg; // 0c = 0x0000001c + u32 touch_state; // 10 = 0x0000001c + u32 device_id; // 14 = 0x43495424 = "$TIC" + u32 spi_config; // 18 = 0xfda00a2e + u16 vendor_id; // 1c = 0x045e = Microsoft Corp. + u16 product_id; // 1e = 0x0c1a + u32 revision; // 20 = 0x00000001 + u32 fw_version; // 24 = 0x05008a8b = 5.0.138.139 (this value looks more random on newer devices) + u32 command; // 28 = 0x00000000 + u32 fw_mode; // 2c = 0x00000000 (for fw update?) + u32 _unknown_30; // 30 = 0x00000000 + u8 eds_minor_ver; // 34 = 0x5e + u8 eds_major_ver; // 35 = 0x03 + u8 interface_rev; // 36 = 0x04 + u8 eu_kernel_ver; // 37 = 0x04 + u32 _unknown_38; // 38 = 0x000001c0 (0x000001c1 after DMA_RX_CODE_RESET) + u32 _unknown_3c; // 3c = 0x00000002 +}; +static_assert(sizeof(struct ithc_device_config) == 64); + +#define RX_CODE_INPUT_REPORT 3 +#define RX_CODE_FEATURE_REPORT 4 +#define RX_CODE_REPORT_DESCRIPTOR 5 +#define RX_CODE_RESET 7 + +#define TX_CODE_SET_FEATURE 3 +#define TX_CODE_GET_FEATURE 4 +#define TX_CODE_OUTPUT_REPORT 5 +#define TX_CODE_GET_REPORT_DESCRIPTOR 7 + +static int ithc_set_device_enabled(struct ithc *ithc, bool enable) +{ + u32 x = ithc->legacy_touch_cfg = + (ithc->legacy_touch_cfg & ~(u32)DEVCFG_TOUCH_MASK) | + DEVCFG_TOUCH_HID_REPORT_ENABLE | + (enable ? DEVCFG_TOUCH_ENABLE | DEVCFG_TOUCH_POWER_STATE(3) : 0); + return ithc_spi_command(ithc, SPI_CMD_CODE_WRITE, + offsetof(struct ithc_device_config, touch_cfg), sizeof(x), &x); +} + +int ithc_legacy_init(struct ithc *ithc) +{ + // Since we don't yet know which SPI config the device wants, use default speed and mode + // initially for reading config data. + CHECK(ithc_set_spi_config, ithc, 2, true, SPI_MODE_SINGLE, SPI_MODE_SINGLE); + + // Setting the following bit seems to make reading the config more reliable. + bitsl_set(&ithc->regs->dma_rx[0].init_unknown, INIT_UNKNOWN_31); + + // Setting this bit may be necessary on ADL devices. + switch (ithc->pci->device) { + case PCI_DEVICE_ID_INTEL_THC_ADL_S_PORT1: + case PCI_DEVICE_ID_INTEL_THC_ADL_S_PORT2: + case PCI_DEVICE_ID_INTEL_THC_ADL_P_PORT1: + case PCI_DEVICE_ID_INTEL_THC_ADL_P_PORT2: + case PCI_DEVICE_ID_INTEL_THC_ADL_M_PORT1: + case PCI_DEVICE_ID_INTEL_THC_ADL_M_PORT2: + bitsl_set(&ithc->regs->dma_rx[0].init_unknown, INIT_UNKNOWN_5); + break; + } + + // Take the touch device out of reset. + bitsl(&ithc->regs->control_bits, CONTROL_QUIESCE, 0); + CHECK_RET(waitl, ithc, &ithc->regs->control_bits, CONTROL_IS_QUIESCED, 0); + for (int retries = 0; ; retries++) { + ithc_log_regs(ithc); + bitsl_set(&ithc->regs->control_bits, CONTROL_NRESET); + if (!waitl(ithc, &ithc->regs->irq_cause, 0xf, 2)) + break; + if (retries > 5) { + pci_err(ithc->pci, "failed to reset device, irq_cause = 0x%08x\n", + readl(&ithc->regs->irq_cause)); + return -ETIMEDOUT; + } + pci_warn(ithc->pci, "invalid irq_cause, retrying reset\n"); + bitsl(&ithc->regs->control_bits, CONTROL_NRESET, 0); + if (msleep_interruptible(1000)) + return -EINTR; + } + ithc_log_regs(ithc); + + CHECK(waitl, ithc, &ithc->regs->dma_rx[0].status, DMA_RX_STATUS_READY, DMA_RX_STATUS_READY); + + // Read configuration data. + u32 spi_cfg; + for (int retries = 0; ; retries++) { + ithc_log_regs(ithc); + struct ithc_device_config config = { 0 }; + CHECK_RET(ithc_spi_command, ithc, SPI_CMD_CODE_READ, 0, sizeof(config), &config); + u32 *p = (void *)&config; + pci_info(ithc->pci, "config: %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x\n", + p[0], p[1], p[2], p[3], p[4], p[5], p[6], p[7], p[8], p[9], p[10], p[11], p[12], p[13], p[14], p[15]); + if (config.device_id == DEVCFG_DEVICE_ID_TIC) { + spi_cfg = config.spi_config; + ithc->vendor_id = config.vendor_id; + ithc->product_id = config.product_id; + ithc->product_rev = config.revision; + ithc->max_rx_size = DEVCFG_DMA_RX_SIZE(config.dma_buf_sizes); + ithc->max_tx_size = DEVCFG_DMA_TX_SIZE(config.dma_buf_sizes); + ithc->legacy_touch_cfg = config.touch_cfg; + ithc->have_config = true; + break; + } + if (retries > 10) { + pci_err(ithc->pci, "failed to read config, unknown device ID 0x%08x\n", + config.device_id); + return -EIO; + } + pci_warn(ithc->pci, "failed to read config, retrying\n"); + if (msleep_interruptible(100)) + return -EINTR; + } + ithc_log_regs(ithc); + + // Apply SPI config and enable touch device. + CHECK_RET(ithc_set_spi_config, ithc, + DEVCFG_SPI_CLKDIV(spi_cfg), (spi_cfg & DEVCFG_SPI_CLKDIV_8) != 0, + spi_cfg & DEVCFG_SPI_SUPPORTS_QUAD ? SPI_MODE_QUAD : + spi_cfg & DEVCFG_SPI_SUPPORTS_DUAL ? SPI_MODE_DUAL : + SPI_MODE_SINGLE, + SPI_MODE_SINGLE); + CHECK_RET(ithc_set_device_enabled, ithc, true); + ithc_log_regs(ithc); + return 0; +} + +void ithc_legacy_exit(struct ithc *ithc) +{ + CHECK(ithc_set_device_enabled, ithc, false); +} + +int ithc_legacy_decode_rx(struct ithc *ithc, const void *src, size_t len, struct ithc_data *dest) +{ + const struct { + u32 code; + u32 data_size; + u32 _unknown[14]; + } *hdr = src; + + if (len < sizeof(*hdr)) + return -ENODATA; + // Note: RX data is not padded, even though TX data must be padded. + if (len != sizeof(*hdr) + hdr->data_size) + return -EMSGSIZE; + + dest->data = hdr + 1; + dest->size = hdr->data_size; + + switch (hdr->code) { + case RX_CODE_RESET: + // The THC sends a reset request when we need to reinitialize the device. + // This usually only happens if we send an invalid command or put the device + // in a bad state. + dest->type = ITHC_DATA_ERROR; + return 0; + case RX_CODE_REPORT_DESCRIPTOR: + // The descriptor is preceded by 8 nul bytes. + if (hdr->data_size < 8) + return -ENODATA; + dest->type = ITHC_DATA_REPORT_DESCRIPTOR; + dest->data = (char *)(hdr + 1) + 8; + dest->size = hdr->data_size - 8; + return 0; + case RX_CODE_INPUT_REPORT: + dest->type = ITHC_DATA_INPUT_REPORT; + return 0; + case RX_CODE_FEATURE_REPORT: + dest->type = ITHC_DATA_GET_FEATURE; + return 0; + default: + return -EINVAL; + } +} + +ssize_t ithc_legacy_encode_tx(struct ithc *ithc, const struct ithc_data *src, void *dest, + size_t maxlen) +{ + struct { + u32 code; + u32 data_size; + } *hdr = dest; + + size_t src_size = src->size; + const void *src_data = src->data; + const u64 get_report_desc_data = 0; + u32 code; + + switch (src->type) { + case ITHC_DATA_SET_FEATURE: + code = TX_CODE_SET_FEATURE; + break; + case ITHC_DATA_GET_FEATURE: + code = TX_CODE_GET_FEATURE; + break; + case ITHC_DATA_OUTPUT_REPORT: + code = TX_CODE_OUTPUT_REPORT; + break; + case ITHC_DATA_REPORT_DESCRIPTOR: + code = TX_CODE_GET_REPORT_DESCRIPTOR; + src_size = sizeof(get_report_desc_data); + src_data = &get_report_desc_data; + break; + default: + return -EINVAL; + } + + // Data must be padded to next 4-byte boundary. + size_t padded = round_up(src_size, 4); + if (sizeof(*hdr) + padded > maxlen) + return -EOVERFLOW; + + // Fill the TX buffer with header and data. + hdr->code = code; + hdr->data_size = src_size; + memcpy_and_pad(hdr + 1, padded, src_data, src_size, 0); + + return sizeof(*hdr) + padded; +} + diff --git a/drivers/hid/ithc/ithc-legacy.h b/drivers/hid/ithc/ithc-legacy.h new file mode 100644 index 000000000000..28d692462072 --- /dev/null +++ b/drivers/hid/ithc/ithc-legacy.h @@ -0,0 +1,8 @@ +/* SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause */ + +int ithc_legacy_init(struct ithc *ithc); +void ithc_legacy_exit(struct ithc *ithc); +int ithc_legacy_decode_rx(struct ithc *ithc, const void *src, size_t len, struct ithc_data *dest); +ssize_t ithc_legacy_encode_tx(struct ithc *ithc, const struct ithc_data *src, void *dest, + size_t maxlen); + diff --git a/drivers/hid/ithc/ithc-main.c b/drivers/hid/ithc/ithc-main.c new file mode 100644 index 000000000000..094d878d671b --- /dev/null +++ b/drivers/hid/ithc/ithc-main.c @@ -0,0 +1,438 @@ +// SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause + +#include "ithc.h" + +MODULE_DESCRIPTION("Intel Touch Host Controller driver"); +MODULE_LICENSE("Dual BSD/GPL"); + +static const struct pci_device_id ithc_pci_tbl[] = { + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_THC_LKF_PORT1) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_THC_LKF_PORT2) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_THC_TGL_LP_PORT1) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_THC_TGL_LP_PORT2) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_THC_TGL_H_PORT1) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_THC_TGL_H_PORT2) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_THC_ADL_S_PORT1) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_THC_ADL_S_PORT2) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_THC_ADL_P_PORT1) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_THC_ADL_P_PORT2) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_THC_ADL_M_PORT1) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_THC_ADL_M_PORT2) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_THC_RPL_S_PORT1) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_THC_RPL_S_PORT2) }, + // MTL and up are handled by drivers/hid/intel-thc-hid + {} +}; +MODULE_DEVICE_TABLE(pci, ithc_pci_tbl); + +// Module parameters + +static bool ithc_use_polling = false; +module_param_named(poll, ithc_use_polling, bool, 0); +MODULE_PARM_DESC(poll, "Use polling instead of interrupts"); + +// Since all known devices seem to use only channel 1, by default we disable channel 0. +static bool ithc_use_rx0 = false; +module_param_named(rx0, ithc_use_rx0, bool, 0); +MODULE_PARM_DESC(rx0, "Use DMA RX channel 0"); + +static bool ithc_use_rx1 = true; +module_param_named(rx1, ithc_use_rx1, bool, 0); +MODULE_PARM_DESC(rx1, "Use DMA RX channel 1"); + +static int ithc_active_ltr_us = -1; +module_param_named(activeltr, ithc_active_ltr_us, int, 0); +MODULE_PARM_DESC(activeltr, "Active LTR value override (in microseconds)"); + +static int ithc_idle_ltr_us = -1; +module_param_named(idleltr, ithc_idle_ltr_us, int, 0); +MODULE_PARM_DESC(idleltr, "Idle LTR value override (in microseconds)"); + +static unsigned int ithc_idle_delay_ms = 1000; +module_param_named(idledelay, ithc_idle_delay_ms, uint, 0); +MODULE_PARM_DESC(idleltr, "Minimum idle time before applying idle LTR value (in milliseconds)"); + +static bool ithc_log_regs_enabled = false; +module_param_named(logregs, ithc_log_regs_enabled, bool, 0); +MODULE_PARM_DESC(logregs, "Log changes in register values (for debugging)"); + +// Interrupts/polling + +static void ithc_disable_interrupts(struct ithc *ithc) +{ + writel(0, &ithc->regs->error_control); + bitsb(&ithc->regs->spi_cmd.control, SPI_CMD_CONTROL_IRQ, 0); + bitsb(&ithc->regs->dma_rx[0].control, DMA_RX_CONTROL_IRQ_UNKNOWN_1 | DMA_RX_CONTROL_IRQ_ERROR | DMA_RX_CONTROL_IRQ_READY | DMA_RX_CONTROL_IRQ_DATA, 0); + bitsb(&ithc->regs->dma_rx[1].control, DMA_RX_CONTROL_IRQ_UNKNOWN_1 | DMA_RX_CONTROL_IRQ_ERROR | DMA_RX_CONTROL_IRQ_READY | DMA_RX_CONTROL_IRQ_DATA, 0); + bitsb(&ithc->regs->dma_tx.control, DMA_TX_CONTROL_IRQ, 0); +} + +static void ithc_clear_dma_rx_interrupts(struct ithc *ithc, unsigned int channel) +{ + writel(DMA_RX_STATUS_ERROR | DMA_RX_STATUS_READY | DMA_RX_STATUS_HAVE_DATA, + &ithc->regs->dma_rx[channel].status); +} + +static void ithc_clear_interrupts(struct ithc *ithc) +{ + writel(0xffffffff, &ithc->regs->error_flags); + writel(ERROR_STATUS_DMA | ERROR_STATUS_SPI, &ithc->regs->error_status); + writel(SPI_CMD_STATUS_DONE | SPI_CMD_STATUS_ERROR, &ithc->regs->spi_cmd.status); + ithc_clear_dma_rx_interrupts(ithc, 0); + ithc_clear_dma_rx_interrupts(ithc, 1); + writel(DMA_TX_STATUS_DONE | DMA_TX_STATUS_ERROR | DMA_TX_STATUS_UNKNOWN_2, + &ithc->regs->dma_tx.status); +} + +static void ithc_idle_timer_callback(struct timer_list *t) +{ + struct ithc *ithc = container_of(t, struct ithc, idle_timer); + ithc_set_ltr_idle(ithc); +} + +static void ithc_process(struct ithc *ithc) +{ + ithc_log_regs(ithc); + + // The THC automatically transitions from LTR idle to active at the start of a DMA transfer. + // It does not appear to automatically go back to idle, so we switch it back after a delay. + mod_timer(&ithc->idle_timer, jiffies + msecs_to_jiffies(ithc_idle_delay_ms)); + + bool rx0 = ithc_use_rx0 && (readl(&ithc->regs->dma_rx[0].status) & (DMA_RX_STATUS_ERROR | DMA_RX_STATUS_HAVE_DATA)) != 0; + bool rx1 = ithc_use_rx1 && (readl(&ithc->regs->dma_rx[1].status) & (DMA_RX_STATUS_ERROR | DMA_RX_STATUS_HAVE_DATA)) != 0; + + // Read and clear error bits + u32 err = readl(&ithc->regs->error_flags); + if (err) { + writel(err, &ithc->regs->error_flags); + if (err & ~ERROR_FLAG_DMA_RX_TIMEOUT) + pci_err(ithc->pci, "error flags: 0x%08x\n", err); + if (err & ERROR_FLAG_DMA_RX_TIMEOUT) + pci_err(ithc->pci, "DMA RX timeout/error (try decreasing activeltr/idleltr if this happens frequently)\n"); + } + + // Process DMA rx + if (ithc_use_rx0) { + ithc_clear_dma_rx_interrupts(ithc, 0); + if (rx0) + ithc_dma_rx(ithc, 0); + } + if (ithc_use_rx1) { + ithc_clear_dma_rx_interrupts(ithc, 1); + if (rx1) + ithc_dma_rx(ithc, 1); + } + + ithc_log_regs(ithc); +} + +static irqreturn_t ithc_interrupt_thread(int irq, void *arg) +{ + struct ithc *ithc = arg; + pci_dbg(ithc->pci, "IRQ! err=%08x/%08x/%08x, cmd=%02x/%08x, rx0=%02x/%08x, rx1=%02x/%08x, tx=%02x/%08x\n", + readl(&ithc->regs->error_control), readl(&ithc->regs->error_status), readl(&ithc->regs->error_flags), + readb(&ithc->regs->spi_cmd.control), readl(&ithc->regs->spi_cmd.status), + readb(&ithc->regs->dma_rx[0].control), readl(&ithc->regs->dma_rx[0].status), + readb(&ithc->regs->dma_rx[1].control), readl(&ithc->regs->dma_rx[1].status), + readb(&ithc->regs->dma_tx.control), readl(&ithc->regs->dma_tx.status)); + ithc_process(ithc); + return IRQ_HANDLED; +} + +static int ithc_poll_thread(void *arg) +{ + struct ithc *ithc = arg; + unsigned int sleep = 100; + while (!kthread_should_stop()) { + u32 n = ithc->dma_rx[1].num_received; + ithc_process(ithc); + // Decrease polling interval to 20ms if we received data, otherwise slowly + // increase it up to 200ms. + sleep = n != ithc->dma_rx[1].num_received ? 20 + : min(200u, sleep + (sleep >> 4) + 1); + msleep_interruptible(sleep); + } + return 0; +} + +// Device initialization and shutdown + +static void ithc_disable(struct ithc *ithc) +{ + bitsl_set(&ithc->regs->control_bits, CONTROL_QUIESCE); + CHECK(waitl, ithc, &ithc->regs->control_bits, CONTROL_IS_QUIESCED, CONTROL_IS_QUIESCED); + bitsl(&ithc->regs->control_bits, CONTROL_NRESET, 0); + bitsb(&ithc->regs->spi_cmd.control, SPI_CMD_CONTROL_SEND, 0); + bitsb(&ithc->regs->dma_tx.control, DMA_TX_CONTROL_SEND, 0); + bitsb(&ithc->regs->dma_rx[0].control, DMA_RX_CONTROL_ENABLE, 0); + bitsb(&ithc->regs->dma_rx[1].control, DMA_RX_CONTROL_ENABLE, 0); + ithc_disable_interrupts(ithc); + ithc_clear_interrupts(ithc); +} + +static int ithc_init_device(struct ithc *ithc) +{ + // Read ACPI config for QuickSPI mode + struct ithc_acpi_config cfg = { 0 }; + CHECK_RET(ithc_read_acpi_config, ithc, &cfg); + if (!cfg.has_config) + pci_info(ithc->pci, "no ACPI config, using legacy mode\n"); + else + ithc_print_acpi_config(ithc, &cfg); + ithc->use_quickspi = cfg.has_config; + + // Shut down device + ithc_log_regs(ithc); + bool was_enabled = (readl(&ithc->regs->control_bits) & CONTROL_NRESET) != 0; + ithc_disable(ithc); + CHECK_RET(waitl, ithc, &ithc->regs->control_bits, CONTROL_READY, CONTROL_READY); + ithc_log_regs(ithc); + + // If the device was previously enabled, wait a bit to make sure it's fully shut down. + if (was_enabled) + if (msleep_interruptible(100)) + return -EINTR; + + // Set Latency Tolerance Reporting config. The device will automatically + // apply these values depending on whether it is active or idle. + // If active value is too high, DMA buffer data can become truncated. + // By default, we set the active LTR value to 50us, and idle to 100ms. + u64 active_ltr_ns = ithc_active_ltr_us >= 0 ? (u64)ithc_active_ltr_us * 1000 + : cfg.has_config && cfg.has_active_ltr ? (u64)cfg.active_ltr << 10 + : 50 * 1000; + u64 idle_ltr_ns = ithc_idle_ltr_us >= 0 ? (u64)ithc_idle_ltr_us * 1000 + : cfg.has_config && cfg.has_idle_ltr ? (u64)cfg.idle_ltr << 10 + : 100 * 1000 * 1000; + ithc_set_ltr_config(ithc, active_ltr_ns, idle_ltr_ns); + + if (ithc->use_quickspi) + CHECK_RET(ithc_quickspi_init, ithc, &cfg); + else + CHECK_RET(ithc_legacy_init, ithc); + + return 0; +} + +int ithc_reset(struct ithc *ithc) +{ + // FIXME This should probably do devres_release_group()+ithc_start(). + // But because this is called during DMA processing, that would have to be done + // asynchronously (schedule_work()?). And with extra locking? + pci_err(ithc->pci, "reset\n"); + CHECK(ithc_init_device, ithc); + if (ithc_use_rx0) + ithc_dma_rx_enable(ithc, 0); + if (ithc_use_rx1) + ithc_dma_rx_enable(ithc, 1); + ithc_log_regs(ithc); + pci_dbg(ithc->pci, "reset completed\n"); + return 0; +} + +static void ithc_stop(void *res) +{ + struct ithc *ithc = res; + pci_dbg(ithc->pci, "stopping\n"); + ithc_log_regs(ithc); + + if (ithc->poll_thread) + CHECK(kthread_stop, ithc->poll_thread); + if (ithc->irq >= 0) + disable_irq(ithc->irq); + if (ithc->use_quickspi) + ithc_quickspi_exit(ithc); + else + ithc_legacy_exit(ithc); + ithc_disable(ithc); + timer_delete_sync(&ithc->idle_timer); + + // Clear DMA config. + for (unsigned int i = 0; i < 2; i++) { + CHECK(waitl, ithc, &ithc->regs->dma_rx[i].status, DMA_RX_STATUS_ENABLED, 0); + lo_hi_writeq(0, &ithc->regs->dma_rx[i].addr); + writeb(0, &ithc->regs->dma_rx[i].num_bufs); + writeb(0, &ithc->regs->dma_rx[i].num_prds); + } + lo_hi_writeq(0, &ithc->regs->dma_tx.addr); + writeb(0, &ithc->regs->dma_tx.num_prds); + + ithc_log_regs(ithc); + pci_dbg(ithc->pci, "stopped\n"); +} + +static void ithc_clear_drvdata(void *res) +{ + struct pci_dev *pci = res; + pci_set_drvdata(pci, NULL); +} + +static int ithc_start(struct pci_dev *pci) +{ + pci_dbg(pci, "starting\n"); + if (pci_get_drvdata(pci)) { + pci_err(pci, "device already initialized\n"); + return -EINVAL; + } + if (!devres_open_group(&pci->dev, ithc_start, GFP_KERNEL)) + return -ENOMEM; + + // Allocate/init main driver struct. + struct ithc *ithc = devm_kzalloc(&pci->dev, sizeof(*ithc), GFP_KERNEL); + if (!ithc) + return -ENOMEM; + ithc->irq = -1; + ithc->pci = pci; + snprintf(ithc->phys, sizeof(ithc->phys), "pci-%s/" DEVNAME, pci_name(pci)); + pci_set_drvdata(pci, ithc); + CHECK_RET(devm_add_action_or_reset, &pci->dev, ithc_clear_drvdata, pci); + if (ithc_log_regs_enabled) + ithc->prev_regs = devm_kzalloc(&pci->dev, sizeof(*ithc->prev_regs), GFP_KERNEL); + + // PCI initialization. + CHECK_RET(pcim_enable_device, pci); + pci_set_master(pci); + CHECK_RET(pcim_iomap_regions, pci, BIT(0), DEVNAME " regs"); + CHECK_RET(dma_set_mask_and_coherent, &pci->dev, DMA_BIT_MASK(64)); + CHECK_RET(pci_set_power_state, pci, PCI_D0); + ithc->regs = pcim_iomap_table(pci)[0]; + + // Allocate IRQ. + if (!ithc_use_polling) { + CHECK_RET(pci_alloc_irq_vectors, pci, 1, 1, PCI_IRQ_MSI | PCI_IRQ_MSIX); + ithc->irq = CHECK(pci_irq_vector, pci, 0); + if (ithc->irq < 0) + return ithc->irq; + } + + // Initialize THC and touch device. + CHECK_RET(ithc_init_device, ithc); + + // Initialize HID and DMA. + CHECK_RET(ithc_hid_init, ithc); + if (ithc_use_rx0) + CHECK_RET(ithc_dma_rx_init, ithc, 0); + if (ithc_use_rx1) + CHECK_RET(ithc_dma_rx_init, ithc, 1); + CHECK_RET(ithc_dma_tx_init, ithc); + + timer_setup(&ithc->idle_timer, ithc_idle_timer_callback, 0); + + // Add ithc_stop() callback AFTER setting up DMA buffers, so that polling/irqs/DMA are + // disabled BEFORE the buffers are freed. + CHECK_RET(devm_add_action_or_reset, &pci->dev, ithc_stop, ithc); + + // Start polling/IRQ. + if (ithc_use_polling) { + pci_info(pci, "using polling instead of irq\n"); + // Use a thread instead of simple timer because we want to be able to sleep. + ithc->poll_thread = kthread_run(ithc_poll_thread, ithc, DEVNAME "poll"); + if (IS_ERR(ithc->poll_thread)) { + int err = PTR_ERR(ithc->poll_thread); + ithc->poll_thread = NULL; + return err; + } + } else { + CHECK_RET(devm_request_threaded_irq, &pci->dev, ithc->irq, NULL, + ithc_interrupt_thread, IRQF_TRIGGER_HIGH | IRQF_ONESHOT, DEVNAME, ithc); + } + + if (ithc_use_rx0) + ithc_dma_rx_enable(ithc, 0); + if (ithc_use_rx1) + ithc_dma_rx_enable(ithc, 1); + + // hid_add_device() can only be called after irq/polling is started and DMA is enabled, + // because it calls ithc_hid_parse() which reads the report descriptor via DMA. + CHECK_RET(hid_add_device, ithc->hid.dev); + + CHECK(ithc_debug_init_device, ithc); + + ithc_set_ltr_idle(ithc); + + pci_dbg(pci, "started\n"); + return 0; +} + +static int ithc_probe(struct pci_dev *pci, const struct pci_device_id *id) +{ + pci_dbg(pci, "device probe\n"); + return ithc_start(pci); +} + +static void ithc_remove(struct pci_dev *pci) +{ + pci_dbg(pci, "device remove\n"); + // all cleanup is handled by devres +} + +// For suspend/resume, we just deinitialize and reinitialize everything. +// TODO It might be cleaner to keep the HID device around, however we would then have to signal +// to userspace that the touch device has lost state and userspace needs to e.g. resend 'set +// feature' requests. Hidraw does not seem to have a facility to do that. +static int ithc_suspend(struct device *dev) +{ + struct pci_dev *pci = to_pci_dev(dev); + pci_dbg(pci, "pm suspend\n"); + devres_release_group(dev, ithc_start); + return 0; +} + +static int ithc_resume(struct device *dev) +{ + struct pci_dev *pci = to_pci_dev(dev); + pci_dbg(pci, "pm resume\n"); + return ithc_start(pci); +} + +static int ithc_freeze(struct device *dev) +{ + struct pci_dev *pci = to_pci_dev(dev); + pci_dbg(pci, "pm freeze\n"); + devres_release_group(dev, ithc_start); + return 0; +} + +static int ithc_thaw(struct device *dev) +{ + struct pci_dev *pci = to_pci_dev(dev); + pci_dbg(pci, "pm thaw\n"); + return ithc_start(pci); +} + +static int ithc_restore(struct device *dev) +{ + struct pci_dev *pci = to_pci_dev(dev); + pci_dbg(pci, "pm restore\n"); + return ithc_start(pci); +} + +static struct pci_driver ithc_driver = { + .name = DEVNAME, + .id_table = ithc_pci_tbl, + .probe = ithc_probe, + .remove = ithc_remove, + .driver.pm = &(const struct dev_pm_ops) { + .suspend = ithc_suspend, + .resume = ithc_resume, + .freeze = ithc_freeze, + .thaw = ithc_thaw, + .restore = ithc_restore, + }, + .driver.probe_type = PROBE_PREFER_ASYNCHRONOUS, +}; + +static int __init ithc_init(void) +{ + ithc_debug_init_module(); + return pci_register_driver(&ithc_driver); +} + +static void __exit ithc_exit(void) +{ + pci_unregister_driver(&ithc_driver); + ithc_debug_exit_module(); +} + +module_init(ithc_init); +module_exit(ithc_exit); + diff --git a/drivers/hid/ithc/ithc-quickspi.c b/drivers/hid/ithc/ithc-quickspi.c new file mode 100644 index 000000000000..e2d1690b8cf8 --- /dev/null +++ b/drivers/hid/ithc/ithc-quickspi.c @@ -0,0 +1,607 @@ +// SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause + +// Some public THC/QuickSPI documentation can be found in: +// - Intel Firmware Support Package repo: https://github.com/intel/FSP +// - HID over SPI (HIDSPI) spec: https://www.microsoft.com/en-us/download/details.aspx?id=103325 + +#include "ithc.h" + +static const guid_t guid_hidspi = + GUID_INIT(0x6e2ac436, 0x0fcf, 0x41af, 0xa2, 0x65, 0xb3, 0x2a, 0x22, 0x0d, 0xcf, 0xab); +static const guid_t guid_thc_quickspi = + GUID_INIT(0x300d35b7, 0xac20, 0x413e, 0x8e, 0x9c, 0x92, 0xe4, 0xda, 0xfd, 0x0a, 0xfe); +static const guid_t guid_thc_ltr = + GUID_INIT(0x84005682, 0x5b71, 0x41a4, 0x8d, 0x66, 0x81, 0x30, 0xf7, 0x87, 0xa1, 0x38); + +// TODO The HIDSPI spec says revision should be 3. Should we try both? +#define DSM_REV 2 + +struct hidspi_header { + u8 type; + u16 len; + u8 id; +} __packed; +static_assert(sizeof(struct hidspi_header) == 4); + +#define HIDSPI_INPUT_TYPE_DATA 1 +#define HIDSPI_INPUT_TYPE_RESET_RESPONSE 3 +#define HIDSPI_INPUT_TYPE_COMMAND_RESPONSE 4 +#define HIDSPI_INPUT_TYPE_GET_FEATURE_RESPONSE 5 +#define HIDSPI_INPUT_TYPE_DEVICE_DESCRIPTOR 7 +#define HIDSPI_INPUT_TYPE_REPORT_DESCRIPTOR 8 +#define HIDSPI_INPUT_TYPE_SET_FEATURE_RESPONSE 9 +#define HIDSPI_INPUT_TYPE_OUTPUT_REPORT_RESPONSE 10 +#define HIDSPI_INPUT_TYPE_GET_INPUT_REPORT_RESPONSE 11 + +#define HIDSPI_OUTPUT_TYPE_DEVICE_DESCRIPTOR_REQUEST 1 +#define HIDSPI_OUTPUT_TYPE_REPORT_DESCRIPTOR_REQUEST 2 +#define HIDSPI_OUTPUT_TYPE_SET_FEATURE 3 +#define HIDSPI_OUTPUT_TYPE_GET_FEATURE 4 +#define HIDSPI_OUTPUT_TYPE_OUTPUT_REPORT 5 +#define HIDSPI_OUTPUT_TYPE_INPUT_REPORT_REQUEST 6 +#define HIDSPI_OUTPUT_TYPE_COMMAND 7 + +struct hidspi_device_descriptor { + u16 wDeviceDescLength; + u16 bcdVersion; + u16 wReportDescLength; + u16 wMaxInputLength; + u16 wMaxOutputLength; + u16 wMaxFragmentLength; + u16 wVendorID; + u16 wProductID; + u16 wVersionID; + u16 wFlags; + u32 dwReserved; +}; +static_assert(sizeof(struct hidspi_device_descriptor) == 24); + +static int read_acpi_u32(struct ithc *ithc, const guid_t *guid, u32 func, u32 *dest) +{ + acpi_handle handle = ACPI_HANDLE(&ithc->pci->dev); + union acpi_object *o = acpi_evaluate_dsm(handle, guid, DSM_REV, func, NULL); + if (!o) + return 0; + if (o->type != ACPI_TYPE_INTEGER) { + pci_err(ithc->pci, "DSM %pUl %u returned type %i instead of integer\n", + guid, func, o->type); + ACPI_FREE(o); + return -1; + } + pci_dbg(ithc->pci, "DSM %pUl %u = 0x%08x\n", guid, func, (u32)o->integer.value); + *dest = (u32)o->integer.value; + ACPI_FREE(o); + return 1; +} + +static int read_acpi_buf(struct ithc *ithc, const guid_t *guid, u32 func, size_t len, u8 *dest) +{ + acpi_handle handle = ACPI_HANDLE(&ithc->pci->dev); + union acpi_object *o = acpi_evaluate_dsm(handle, guid, DSM_REV, func, NULL); + if (!o) + return 0; + if (o->type != ACPI_TYPE_BUFFER) { + pci_err(ithc->pci, "DSM %pUl %u returned type %i instead of buffer\n", + guid, func, o->type); + ACPI_FREE(o); + return -1; + } + if (o->buffer.length != len) { + pci_err(ithc->pci, "DSM %pUl %u returned len %u instead of %zu\n", + guid, func, o->buffer.length, len); + ACPI_FREE(o); + return -1; + } + memcpy(dest, o->buffer.pointer, len); + pci_dbg(ithc->pci, "DSM %pUl %u = 0x%02x\n", guid, func, dest[0]); + ACPI_FREE(o); + return 1; +} + +int ithc_read_acpi_config(struct ithc *ithc, struct ithc_acpi_config *cfg) +{ + int r; + acpi_handle handle = ACPI_HANDLE(&ithc->pci->dev); + + cfg->has_config = acpi_check_dsm(handle, &guid_hidspi, DSM_REV, BIT(0)); + if (!cfg->has_config) + return 0; + + // HIDSPI settings + + r = read_acpi_u32(ithc, &guid_hidspi, 1, &cfg->input_report_header_address); + if (r < 0) + return r; + cfg->has_input_report_header_address = r > 0; + if (r > 0 && cfg->input_report_header_address > 0xffffff) { + pci_err(ithc->pci, "Invalid input report header address 0x%x\n", + cfg->input_report_header_address); + return -1; + } + + r = read_acpi_u32(ithc, &guid_hidspi, 2, &cfg->input_report_body_address); + if (r < 0) + return r; + cfg->has_input_report_body_address = r > 0; + if (r > 0 && cfg->input_report_body_address > 0xffffff) { + pci_err(ithc->pci, "Invalid input report body address 0x%x\n", + cfg->input_report_body_address); + return -1; + } + + r = read_acpi_u32(ithc, &guid_hidspi, 3, &cfg->output_report_body_address); + if (r < 0) + return r; + cfg->has_output_report_body_address = r > 0; + if (r > 0 && cfg->output_report_body_address > 0xffffff) { + pci_err(ithc->pci, "Invalid output report body address 0x%x\n", + cfg->output_report_body_address); + return -1; + } + + r = read_acpi_buf(ithc, &guid_hidspi, 4, sizeof(cfg->read_opcode), &cfg->read_opcode); + if (r < 0) + return r; + cfg->has_read_opcode = r > 0; + + r = read_acpi_buf(ithc, &guid_hidspi, 5, sizeof(cfg->write_opcode), &cfg->write_opcode); + if (r < 0) + return r; + cfg->has_write_opcode = r > 0; + + u32 flags; + r = read_acpi_u32(ithc, &guid_hidspi, 6, &flags); + if (r < 0) + return r; + cfg->has_read_mode = cfg->has_write_mode = r > 0; + if (r > 0) { + cfg->read_mode = (flags >> 14) & 3; + cfg->write_mode = flags & BIT(13) ? cfg->read_mode : SPI_MODE_SINGLE; + } + + // Quick SPI settings + + r = read_acpi_u32(ithc, &guid_thc_quickspi, 1, &cfg->spi_frequency); + if (r < 0) + return r; + cfg->has_spi_frequency = r > 0; + + r = read_acpi_u32(ithc, &guid_thc_quickspi, 2, &cfg->limit_packet_size); + if (r < 0) + return r; + cfg->has_limit_packet_size = r > 0; + + r = read_acpi_u32(ithc, &guid_thc_quickspi, 3, &cfg->tx_delay); + if (r < 0) + return r; + cfg->has_tx_delay = r > 0; + if (r > 0) + cfg->tx_delay &= 0xffff; + + // LTR settings + + r = read_acpi_u32(ithc, &guid_thc_ltr, 1, &cfg->active_ltr); + if (r < 0) + return r; + cfg->has_active_ltr = r > 0; + if (r > 0 && (!cfg->active_ltr || cfg->active_ltr > 0x3ff)) { + if (cfg->active_ltr != 0xffffffff) + pci_warn(ithc->pci, "Ignoring invalid active LTR value 0x%x\n", + cfg->active_ltr); + cfg->active_ltr = 500; + } + + r = read_acpi_u32(ithc, &guid_thc_ltr, 2, &cfg->idle_ltr); + if (r < 0) + return r; + cfg->has_idle_ltr = r > 0; + if (r > 0 && (!cfg->idle_ltr || cfg->idle_ltr > 0x3ff)) { + if (cfg->idle_ltr != 0xffffffff) + pci_warn(ithc->pci, "Ignoring invalid idle LTR value 0x%x\n", + cfg->idle_ltr); + cfg->idle_ltr = 500; + if (cfg->has_active_ltr && cfg->active_ltr > cfg->idle_ltr) + cfg->idle_ltr = cfg->active_ltr; + } + + return 0; +} + +void ithc_print_acpi_config(struct ithc *ithc, const struct ithc_acpi_config *cfg) +{ + if (!cfg->has_config) { + pci_info(ithc->pci, "No ACPI config"); + return; + } + + char input_report_header_address[16] = "-"; + if (cfg->has_input_report_header_address) + sprintf(input_report_header_address, "0x%x", cfg->input_report_header_address); + char input_report_body_address[16] = "-"; + if (cfg->has_input_report_body_address) + sprintf(input_report_body_address, "0x%x", cfg->input_report_body_address); + char output_report_body_address[16] = "-"; + if (cfg->has_output_report_body_address) + sprintf(output_report_body_address, "0x%x", cfg->output_report_body_address); + char read_opcode[16] = "-"; + if (cfg->has_read_opcode) + sprintf(read_opcode, "0x%02x", cfg->read_opcode); + char write_opcode[16] = "-"; + if (cfg->has_write_opcode) + sprintf(write_opcode, "0x%02x", cfg->write_opcode); + char read_mode[16] = "-"; + if (cfg->has_read_mode) + sprintf(read_mode, "%i", cfg->read_mode); + char write_mode[16] = "-"; + if (cfg->has_write_mode) + sprintf(write_mode, "%i", cfg->write_mode); + char spi_frequency[16] = "-"; + if (cfg->has_spi_frequency) + sprintf(spi_frequency, "%u", cfg->spi_frequency); + char limit_packet_size[16] = "-"; + if (cfg->has_limit_packet_size) + sprintf(limit_packet_size, "%u", cfg->limit_packet_size); + char tx_delay[16] = "-"; + if (cfg->has_tx_delay) + sprintf(tx_delay, "%u", cfg->tx_delay); + char active_ltr[16] = "-"; + if (cfg->has_active_ltr) + sprintf(active_ltr, "%u", cfg->active_ltr); + char idle_ltr[16] = "-"; + if (cfg->has_idle_ltr) + sprintf(idle_ltr, "%u", cfg->idle_ltr); + + pci_info(ithc->pci, "ACPI config: InputHeaderAddr=%s InputBodyAddr=%s OutputBodyAddr=%s ReadOpcode=%s WriteOpcode=%s ReadMode=%s WriteMode=%s Frequency=%s LimitPacketSize=%s TxDelay=%s ActiveLTR=%s IdleLTR=%s\n", + input_report_header_address, input_report_body_address, output_report_body_address, + read_opcode, write_opcode, read_mode, write_mode, + spi_frequency, limit_packet_size, tx_delay, active_ltr, idle_ltr); +} + +static void set_opcode(struct ithc *ithc, size_t i, u8 opcode) +{ + writeb(opcode, &ithc->regs->opcode[i].header); + writeb(opcode, &ithc->regs->opcode[i].single); + writeb(opcode, &ithc->regs->opcode[i].dual); + writeb(opcode, &ithc->regs->opcode[i].quad); +} + +static int ithc_quickspi_init_regs(struct ithc *ithc, const struct ithc_acpi_config *cfg) +{ + pci_dbg(ithc->pci, "initializing QuickSPI registers\n"); + + // SPI frequency and mode + if (!cfg->has_spi_frequency || !cfg->spi_frequency) { + pci_err(ithc->pci, "Missing SPI frequency in configuration\n"); + return -EINVAL; + } + unsigned int clkdiv = DIV_ROUND_UP(SPI_CLK_FREQ_BASE, cfg->spi_frequency); + bool clkdiv8 = clkdiv > 7; + if (clkdiv8) + clkdiv = min(7u, DIV_ROUND_UP(clkdiv, 8u)); + if (!clkdiv) + clkdiv = 1; + CHECK_RET(ithc_set_spi_config, ithc, clkdiv, clkdiv8, + cfg->has_read_mode ? cfg->read_mode : SPI_MODE_SINGLE, + cfg->has_write_mode ? cfg->write_mode : SPI_MODE_SINGLE); + + // SPI addresses and opcodes + if (cfg->has_input_report_header_address) + writel(cfg->input_report_header_address, &ithc->regs->spi_header_addr); + if (cfg->has_input_report_body_address) { + writel(cfg->input_report_body_address, &ithc->regs->dma_rx[0].spi_addr); + writel(cfg->input_report_body_address, &ithc->regs->dma_rx[1].spi_addr); + } + if (cfg->has_output_report_body_address) + writel(cfg->output_report_body_address, &ithc->regs->dma_tx.spi_addr); + + switch (ithc->pci->device) { + // LKF/TGL don't support QuickSPI. + // For ADL, opcode layout is RX/TX/unused. + case PCI_DEVICE_ID_INTEL_THC_ADL_S_PORT1: + case PCI_DEVICE_ID_INTEL_THC_ADL_S_PORT2: + case PCI_DEVICE_ID_INTEL_THC_ADL_P_PORT1: + case PCI_DEVICE_ID_INTEL_THC_ADL_P_PORT2: + case PCI_DEVICE_ID_INTEL_THC_ADL_M_PORT1: + case PCI_DEVICE_ID_INTEL_THC_ADL_M_PORT2: + if (cfg->has_read_opcode) { + set_opcode(ithc, 0, cfg->read_opcode); + } + if (cfg->has_write_opcode) { + set_opcode(ithc, 1, cfg->write_opcode); + } + break; + // For MTL, opcode layout was changed to RX/RX/TX. + // (RPL layout is unknown.) + default: + if (cfg->has_read_opcode) { + set_opcode(ithc, 0, cfg->read_opcode); + set_opcode(ithc, 1, cfg->read_opcode); + } + if (cfg->has_write_opcode) { + set_opcode(ithc, 2, cfg->write_opcode); + } + break; + } + + ithc_log_regs(ithc); + + // The rest... + bitsl_set(&ithc->regs->dma_rx[0].init_unknown, INIT_UNKNOWN_31); + + bitsl(&ithc->regs->quickspi_config1, + QUICKSPI_CONFIG1_UNKNOWN_0(0xff) | QUICKSPI_CONFIG1_UNKNOWN_5(0xff) | + QUICKSPI_CONFIG1_UNKNOWN_10(0xff) | QUICKSPI_CONFIG1_UNKNOWN_16(0xffff), + QUICKSPI_CONFIG1_UNKNOWN_0(4) | QUICKSPI_CONFIG1_UNKNOWN_5(4) | + QUICKSPI_CONFIG1_UNKNOWN_10(22) | QUICKSPI_CONFIG1_UNKNOWN_16(2)); + + bitsl(&ithc->regs->quickspi_config2, + QUICKSPI_CONFIG2_UNKNOWN_0(0xff) | QUICKSPI_CONFIG2_UNKNOWN_5(0xff) | + QUICKSPI_CONFIG2_UNKNOWN_12(0xff), + QUICKSPI_CONFIG2_UNKNOWN_0(8) | QUICKSPI_CONFIG2_UNKNOWN_5(14) | + QUICKSPI_CONFIG2_UNKNOWN_12(2)); + + u32 pktsize = cfg->has_limit_packet_size && cfg->limit_packet_size == 1 ? 4 : 0x80; + bitsl(&ithc->regs->spi_config, + SPI_CONFIG_READ_PACKET_SIZE(0xfff) | SPI_CONFIG_WRITE_PACKET_SIZE(0xfff), + SPI_CONFIG_READ_PACKET_SIZE(pktsize) | SPI_CONFIG_WRITE_PACKET_SIZE(pktsize)); + + bitsl_set(&ithc->regs->quickspi_config2, + QUICKSPI_CONFIG2_UNKNOWN_16 | QUICKSPI_CONFIG2_UNKNOWN_17); + bitsl(&ithc->regs->quickspi_config2, + QUICKSPI_CONFIG2_DISABLE_READ_ADDRESS_INCREMENT | + QUICKSPI_CONFIG2_DISABLE_WRITE_ADDRESS_INCREMENT | + QUICKSPI_CONFIG2_ENABLE_WRITE_STREAMING_MODE, 0); + + return 0; +} + +static int wait_for_report(struct ithc *ithc) +{ + CHECK_RET(waitl, ithc, &ithc->regs->dma_rx[0].status, + DMA_RX_STATUS_READY, DMA_RX_STATUS_READY); + writel(DMA_RX_STATUS_READY, &ithc->regs->dma_rx[0].status); + + u32 h = readl(&ithc->regs->input_header); + ithc_log_regs(ithc); + if (INPUT_HEADER_SYNC(h) != INPUT_HEADER_SYNC_VALUE + || INPUT_HEADER_VERSION(h) != INPUT_HEADER_VERSION_VALUE) { + pci_err(ithc->pci, "invalid input report frame header 0x%08x\n", h); + return -ENODATA; + } + return INPUT_HEADER_REPORT_LENGTH(h) * 4; +} + +static int ithc_quickspi_init_hidspi(struct ithc *ithc, const struct ithc_acpi_config *cfg) +{ + pci_dbg(ithc->pci, "initializing HIDSPI\n"); + + // HIDSPI initialization sequence: + // "1. The host shall invoke the ACPI reset method to clear the device state." + acpi_status s = acpi_evaluate_object(ACPI_HANDLE(&ithc->pci->dev), "_RST", NULL, NULL); + if (ACPI_FAILURE(s)) { + pci_err(ithc->pci, "ACPI reset failed\n"); + return -EIO; + } + + bitsl(&ithc->regs->control_bits, CONTROL_QUIESCE, 0); + + // "2. Within 1 second, the device shall signal an interrupt and make available to the host + // an input report containing a device reset response." + int size = wait_for_report(ithc); + if (size < 0) + return size; + if (size < sizeof(struct hidspi_header)) { + pci_err(ithc->pci, "SPI data size too small for reset response (%u)\n", size); + return -EMSGSIZE; + } + + // "3. The host shall read the reset response from the device at the Input Report addresses + // specified in ACPI." + u32 in_addr = cfg->has_input_report_body_address ? cfg->input_report_body_address : 0x1000; + struct { + struct hidspi_header header; + union { + struct hidspi_device_descriptor device_desc; + u32 data[16]; + }; + } resp = { 0 }; + if (size > sizeof(resp)) { + pci_err(ithc->pci, "SPI data size for reset response too big (%u)\n", size); + return -EMSGSIZE; + } + CHECK_RET(ithc_spi_command, ithc, SPI_CMD_CODE_READ, in_addr, size, &resp); + if (resp.header.type != HIDSPI_INPUT_TYPE_RESET_RESPONSE) { + pci_err(ithc->pci, "received type %i instead of reset response\n", resp.header.type); + return -ENOMSG; + } + + // "4. The host shall then write an Output Report to the device at the Output Report Address + // specified in ACPI, requesting the Device Descriptor from the device." + u32 out_addr = cfg->has_output_report_body_address ? cfg->output_report_body_address : 0x1000; + struct hidspi_header req = { .type = HIDSPI_OUTPUT_TYPE_DEVICE_DESCRIPTOR_REQUEST }; + CHECK_RET(ithc_spi_command, ithc, SPI_CMD_CODE_WRITE, out_addr, sizeof(req), &req); + + // "5. Within 1 second, the device shall signal an interrupt and make available to the host + // an input report containing the Device Descriptor." + size = wait_for_report(ithc); + if (size < 0) + return size; + if (size < sizeof(resp.header) + sizeof(resp.device_desc)) { + pci_err(ithc->pci, "SPI data size too small for device descriptor (%u)\n", size); + return -EMSGSIZE; + } + + // "6. The host shall read the Device Descriptor from the Input Report addresses specified + // in ACPI." + if (size > sizeof(resp)) { + pci_err(ithc->pci, "SPI data size for device descriptor too big (%u)\n", size); + return -EMSGSIZE; + } + memset(&resp, 0, sizeof(resp)); + CHECK_RET(ithc_spi_command, ithc, SPI_CMD_CODE_READ, in_addr, size, &resp); + if (resp.header.type != HIDSPI_INPUT_TYPE_DEVICE_DESCRIPTOR) { + pci_err(ithc->pci, "received type %i instead of device descriptor\n", + resp.header.type); + return -ENOMSG; + } + struct hidspi_device_descriptor *d = &resp.device_desc; + if (resp.header.len < sizeof(*d)) { + pci_err(ithc->pci, "response too small for device descriptor (%u)\n", + resp.header.len); + return -EMSGSIZE; + } + if (d->wDeviceDescLength != sizeof(*d)) { + pci_err(ithc->pci, "invalid device descriptor length (%u)\n", + d->wDeviceDescLength); + return -EMSGSIZE; + } + + pci_info(ithc->pci, "Device descriptor: bcdVersion=0x%04x wReportDescLength=%u wMaxInputLength=%u wMaxOutputLength=%u wMaxFragmentLength=%u wVendorID=0x%04x wProductID=0x%04x wVersionID=0x%04x wFlags=0x%04x dwReserved=0x%08x\n", + d->bcdVersion, d->wReportDescLength, + d->wMaxInputLength, d->wMaxOutputLength, d->wMaxFragmentLength, + d->wVendorID, d->wProductID, d->wVersionID, + d->wFlags, d->dwReserved); + + ithc->vendor_id = d->wVendorID; + ithc->product_id = d->wProductID; + ithc->product_rev = d->wVersionID; + ithc->max_rx_size = max_t(u32, d->wMaxInputLength, + d->wReportDescLength + sizeof(struct hidspi_header)); + ithc->max_tx_size = d->wMaxOutputLength; + ithc->have_config = true; + + // "7. The device and host shall then enter their "Ready" states - where the device may + // begin sending Input Reports, and the device shall be prepared for Output Reports from + // the host." + + return 0; +} + +int ithc_quickspi_init(struct ithc *ithc, const struct ithc_acpi_config *cfg) +{ + bitsl_set(&ithc->regs->control_bits, CONTROL_QUIESCE); + CHECK_RET(waitl, ithc, &ithc->regs->control_bits, CONTROL_IS_QUIESCED, CONTROL_IS_QUIESCED); + + ithc_log_regs(ithc); + CHECK_RET(ithc_quickspi_init_regs, ithc, cfg); + ithc_log_regs(ithc); + CHECK_RET(ithc_quickspi_init_hidspi, ithc, cfg); + ithc_log_regs(ithc); + + // This value is set to 2 in ithc_quickspi_init_regs(). It needs to be set to 1 here, + // otherwise DMA will not work. Maybe selects between DMA and PIO mode? + bitsl(&ithc->regs->quickspi_config1, + QUICKSPI_CONFIG1_UNKNOWN_16(0xffff), QUICKSPI_CONFIG1_UNKNOWN_16(1)); + + // TODO Do we need to set any of the following bits here? + //bitsb_set(&ithc->regs->dma_rx[1].control2, DMA_RX_CONTROL2_UNKNOWN_4); + //bitsb_set(&ithc->regs->dma_rx[0].control2, DMA_RX_CONTROL2_UNKNOWN_5); + //bitsb_set(&ithc->regs->dma_rx[1].control2, DMA_RX_CONTROL2_UNKNOWN_5); + //bitsl_set(&ithc->regs->dma_rx[0].init_unknown, INIT_UNKNOWN_3); + //bitsl_set(&ithc->regs->dma_rx[0].init_unknown, INIT_UNKNOWN_31); + + ithc_log_regs(ithc); + + return 0; +} + +void ithc_quickspi_exit(struct ithc *ithc) +{ + // TODO Should we send HIDSPI 'power off' command? + //struct hidspi_header h = { .type = HIDSPI_OUTPUT_TYPE_COMMAND, .id = 3, }; + //struct ithc_data d = { .type = ITHC_DATA_RAW, .data = &h, .size = sizeof(h) }; + //CHECK(ithc_dma_tx, ithc, &d); // or ithc_spi_command() +} + +int ithc_quickspi_decode_rx(struct ithc *ithc, const void *src, size_t len, struct ithc_data *dest) +{ + const struct hidspi_header *hdr = src; + + if (len < sizeof(*hdr)) + return -ENODATA; + // TODO Do we need to handle HIDSPI packet fragmentation? + if (len < sizeof(*hdr) + hdr->len) + return -EMSGSIZE; + if (len > round_up(sizeof(*hdr) + hdr->len, 4)) + return -EMSGSIZE; + + switch (hdr->type) { + case HIDSPI_INPUT_TYPE_RESET_RESPONSE: + // TODO "When the device detects an error condition, it may interrupt and make + // available to the host an Input Report containing an unsolicited Reset Response. + // After receiving an unsolicited Reset Response, the host shall initiate the + // request procedure from step (4) in the [HIDSPI initialization] process." + dest->type = ITHC_DATA_ERROR; + return 0; + case HIDSPI_INPUT_TYPE_REPORT_DESCRIPTOR: + dest->type = ITHC_DATA_REPORT_DESCRIPTOR; + dest->data = hdr + 1; + dest->size = hdr->len; + return 0; + case HIDSPI_INPUT_TYPE_DATA: + case HIDSPI_INPUT_TYPE_GET_INPUT_REPORT_RESPONSE: + dest->type = ITHC_DATA_INPUT_REPORT; + dest->data = &hdr->id; + dest->size = hdr->len + 1; + return 0; + case HIDSPI_INPUT_TYPE_GET_FEATURE_RESPONSE: + dest->type = ITHC_DATA_GET_FEATURE; + dest->data = &hdr->id; + dest->size = hdr->len + 1; + return 0; + case HIDSPI_INPUT_TYPE_SET_FEATURE_RESPONSE: + case HIDSPI_INPUT_TYPE_OUTPUT_REPORT_RESPONSE: + dest->type = ITHC_DATA_IGNORE; + return 0; + default: + return -EINVAL; + } +} + +ssize_t ithc_quickspi_encode_tx(struct ithc *ithc, const struct ithc_data *src, void *dest, + size_t maxlen) +{ + struct hidspi_header *hdr = dest; + + size_t src_size = src->size; + const u8 *src_data = src->data; + u8 type; + + switch (src->type) { + case ITHC_DATA_SET_FEATURE: + type = HIDSPI_OUTPUT_TYPE_SET_FEATURE; + break; + case ITHC_DATA_GET_FEATURE: + type = HIDSPI_OUTPUT_TYPE_GET_FEATURE; + break; + case ITHC_DATA_OUTPUT_REPORT: + type = HIDSPI_OUTPUT_TYPE_OUTPUT_REPORT; + break; + case ITHC_DATA_REPORT_DESCRIPTOR: + type = HIDSPI_OUTPUT_TYPE_REPORT_DESCRIPTOR_REQUEST; + src_size = 0; + break; + default: + return -EINVAL; + } + + u8 id = 0; + if (src_size) { + id = *src_data++; + src_size--; + } + + // Data must be padded to next 4-byte boundary. + size_t padded = round_up(src_size, 4); + if (sizeof(*hdr) + padded > maxlen) + return -EOVERFLOW; + + // Fill the TX buffer with header and data. + hdr->type = type; + hdr->len = (u16)src_size; + hdr->id = id; + memcpy_and_pad(hdr + 1, padded, src_data, src_size, 0); + + return sizeof(*hdr) + padded; +} + diff --git a/drivers/hid/ithc/ithc-quickspi.h b/drivers/hid/ithc/ithc-quickspi.h new file mode 100644 index 000000000000..74d882f6b2f0 --- /dev/null +++ b/drivers/hid/ithc/ithc-quickspi.h @@ -0,0 +1,39 @@ +/* SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause */ + +struct ithc_acpi_config { + bool has_config: 1; + bool has_input_report_header_address: 1; + bool has_input_report_body_address: 1; + bool has_output_report_body_address: 1; + bool has_read_opcode: 1; + bool has_write_opcode: 1; + bool has_read_mode: 1; + bool has_write_mode: 1; + bool has_spi_frequency: 1; + bool has_limit_packet_size: 1; + bool has_tx_delay: 1; + bool has_active_ltr: 1; + bool has_idle_ltr: 1; + u32 input_report_header_address; + u32 input_report_body_address; + u32 output_report_body_address; + u8 read_opcode; + u8 write_opcode; + u8 read_mode; + u8 write_mode; + u32 spi_frequency; + u32 limit_packet_size; + u32 tx_delay; // us/10 // TODO use? + u32 active_ltr; // ns/1024 + u32 idle_ltr; // ns/1024 +}; + +int ithc_read_acpi_config(struct ithc *ithc, struct ithc_acpi_config *cfg); +void ithc_print_acpi_config(struct ithc *ithc, const struct ithc_acpi_config *cfg); + +int ithc_quickspi_init(struct ithc *ithc, const struct ithc_acpi_config *cfg); +void ithc_quickspi_exit(struct ithc *ithc); +int ithc_quickspi_decode_rx(struct ithc *ithc, const void *src, size_t len, struct ithc_data *dest); +ssize_t ithc_quickspi_encode_tx(struct ithc *ithc, const struct ithc_data *src, void *dest, + size_t maxlen); + diff --git a/drivers/hid/ithc/ithc-regs.c b/drivers/hid/ithc/ithc-regs.c new file mode 100644 index 000000000000..c0f13506af20 --- /dev/null +++ b/drivers/hid/ithc/ithc-regs.c @@ -0,0 +1,154 @@ +// SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause + +#include "ithc.h" + +#define reg_num(r) (0x1fff & (u16)(__force u64)(r)) + +void bitsl(__iomem u32 *reg, u32 mask, u32 val) +{ + if (val & ~mask) + pr_err("register 0x%x: invalid value 0x%x for bitmask 0x%x\n", + reg_num(reg), val, mask); + writel((readl(reg) & ~mask) | (val & mask), reg); +} + +void bitsb(__iomem u8 *reg, u8 mask, u8 val) +{ + if (val & ~mask) + pr_err("register 0x%x: invalid value 0x%x for bitmask 0x%x\n", + reg_num(reg), val, mask); + writeb((readb(reg) & ~mask) | (val & mask), reg); +} + +int waitl(struct ithc *ithc, __iomem u32 *reg, u32 mask, u32 val) +{ + ithc_log_regs(ithc); + pci_dbg(ithc->pci, "waiting for reg 0x%04x mask 0x%08x val 0x%08x\n", + reg_num(reg), mask, val); + u32 x; + if (readl_poll_timeout(reg, x, (x & mask) == val, 200, 1000*1000)) { + ithc_log_regs(ithc); + pci_err(ithc->pci, "timed out waiting for reg 0x%04x mask 0x%08x val 0x%08x\n", + reg_num(reg), mask, val); + return -ETIMEDOUT; + } + ithc_log_regs(ithc); + pci_dbg(ithc->pci, "done waiting\n"); + return 0; +} + +int waitb(struct ithc *ithc, __iomem u8 *reg, u8 mask, u8 val) +{ + ithc_log_regs(ithc); + pci_dbg(ithc->pci, "waiting for reg 0x%04x mask 0x%02x val 0x%02x\n", + reg_num(reg), mask, val); + u8 x; + if (readb_poll_timeout(reg, x, (x & mask) == val, 200, 1000*1000)) { + ithc_log_regs(ithc); + pci_err(ithc->pci, "timed out waiting for reg 0x%04x mask 0x%02x val 0x%02x\n", + reg_num(reg), mask, val); + return -ETIMEDOUT; + } + ithc_log_regs(ithc); + pci_dbg(ithc->pci, "done waiting\n"); + return 0; +} + +static void calc_ltr(u64 *ns, unsigned int *val, unsigned int *scale) +{ + unsigned int s = 0; + u64 v = *ns; + while (v > 0x3ff) { + s++; + v >>= 5; + } + if (s > 5) { + s = 5; + v = 0x3ff; + } + *val = v; + *scale = s; + *ns = v << (5 * s); +} + +void ithc_set_ltr_config(struct ithc *ithc, u64 active_ltr_ns, u64 idle_ltr_ns) +{ + unsigned int active_val, active_scale, idle_val, idle_scale; + calc_ltr(&active_ltr_ns, &active_val, &active_scale); + calc_ltr(&idle_ltr_ns, &idle_val, &idle_scale); + pci_dbg(ithc->pci, "setting active LTR value to %llu ns, idle LTR value to %llu ns\n", + active_ltr_ns, idle_ltr_ns); + writel(LTR_CONFIG_ENABLE_ACTIVE | LTR_CONFIG_ENABLE_IDLE | LTR_CONFIG_APPLY | + LTR_CONFIG_ACTIVE_LTR_SCALE(active_scale) | LTR_CONFIG_ACTIVE_LTR_VALUE(active_val) | + LTR_CONFIG_IDLE_LTR_SCALE(idle_scale) | LTR_CONFIG_IDLE_LTR_VALUE(idle_val), + &ithc->regs->ltr_config); +} + +void ithc_set_ltr_idle(struct ithc *ithc) +{ + u32 ltr = readl(&ithc->regs->ltr_config); + switch (ltr & (LTR_CONFIG_STATUS_ACTIVE | LTR_CONFIG_STATUS_IDLE)) { + case LTR_CONFIG_STATUS_IDLE: + break; + case LTR_CONFIG_STATUS_ACTIVE: + writel(ltr | LTR_CONFIG_TOGGLE | LTR_CONFIG_APPLY, &ithc->regs->ltr_config); + break; + default: + pci_err(ithc->pci, "invalid LTR state 0x%08x\n", ltr); + break; + } +} + +int ithc_set_spi_config(struct ithc *ithc, u8 clkdiv, bool clkdiv8, u8 read_mode, u8 write_mode) +{ + if (clkdiv == 0 || clkdiv > 7 || read_mode > SPI_MODE_QUAD || write_mode > SPI_MODE_QUAD) + return -EINVAL; + static const char * const modes[] = { "single", "dual", "quad" }; + pci_dbg(ithc->pci, "setting SPI frequency to %i Hz, %s read, %s write\n", + SPI_CLK_FREQ_BASE / (clkdiv * (clkdiv8 ? 8 : 1)), + modes[read_mode], modes[write_mode]); + bitsl(&ithc->regs->spi_config, + SPI_CONFIG_READ_MODE(0xff) | SPI_CONFIG_READ_CLKDIV(0xff) | + SPI_CONFIG_WRITE_MODE(0xff) | SPI_CONFIG_WRITE_CLKDIV(0xff) | + SPI_CONFIG_CLKDIV_8, + SPI_CONFIG_READ_MODE(read_mode) | SPI_CONFIG_READ_CLKDIV(clkdiv) | + SPI_CONFIG_WRITE_MODE(write_mode) | SPI_CONFIG_WRITE_CLKDIV(clkdiv) | + (clkdiv8 ? SPI_CONFIG_CLKDIV_8 : 0)); + return 0; +} + +int ithc_spi_command(struct ithc *ithc, u8 command, u32 offset, u32 size, void *data) +{ + pci_dbg(ithc->pci, "SPI command %u, size %u, offset 0x%x\n", command, size, offset); + if (size > sizeof(ithc->regs->spi_cmd.data)) + return -EINVAL; + + // Wait if the device is still busy. + CHECK_RET(waitl, ithc, &ithc->regs->spi_cmd.status, SPI_CMD_STATUS_BUSY, 0); + // Clear result flags. + writel(SPI_CMD_STATUS_DONE | SPI_CMD_STATUS_ERROR, &ithc->regs->spi_cmd.status); + + // Init SPI command data. + writeb(command, &ithc->regs->spi_cmd.code); + writew(size, &ithc->regs->spi_cmd.size); + writel(offset, &ithc->regs->spi_cmd.offset); + u32 *p = data, n = (size + 3) / 4; + for (u32 i = 0; i < n; i++) + writel(p[i], &ithc->regs->spi_cmd.data[i]); + + // Start transmission. + bitsb_set(&ithc->regs->spi_cmd.control, SPI_CMD_CONTROL_SEND); + CHECK_RET(waitl, ithc, &ithc->regs->spi_cmd.status, SPI_CMD_STATUS_BUSY, 0); + + // Read response. + if ((readl(&ithc->regs->spi_cmd.status) & (SPI_CMD_STATUS_DONE | SPI_CMD_STATUS_ERROR)) != SPI_CMD_STATUS_DONE) + return -EIO; + if (readw(&ithc->regs->spi_cmd.size) != size) + return -EMSGSIZE; + for (u32 i = 0; i < n; i++) + p[i] = readl(&ithc->regs->spi_cmd.data[i]); + + writel(SPI_CMD_STATUS_DONE | SPI_CMD_STATUS_ERROR, &ithc->regs->spi_cmd.status); + return 0; +} + diff --git a/drivers/hid/ithc/ithc-regs.h b/drivers/hid/ithc/ithc-regs.h new file mode 100644 index 000000000000..4f541fe533fa --- /dev/null +++ b/drivers/hid/ithc/ithc-regs.h @@ -0,0 +1,211 @@ +/* SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause */ + +#define LTR_CONFIG_ENABLE_ACTIVE BIT(0) +#define LTR_CONFIG_TOGGLE BIT(1) +#define LTR_CONFIG_ENABLE_IDLE BIT(2) +#define LTR_CONFIG_APPLY BIT(3) +#define LTR_CONFIG_IDLE_LTR_SCALE(x) (((x) & 7) << 4) +#define LTR_CONFIG_IDLE_LTR_VALUE(x) (((x) & 0x3ff) << 7) +#define LTR_CONFIG_ACTIVE_LTR_SCALE(x) (((x) & 7) << 17) +#define LTR_CONFIG_ACTIVE_LTR_VALUE(x) (((x) & 0x3ff) << 20) +#define LTR_CONFIG_STATUS_ACTIVE BIT(30) +#define LTR_CONFIG_STATUS_IDLE BIT(31) + +#define CONTROL_QUIESCE BIT(1) +#define CONTROL_IS_QUIESCED BIT(2) +#define CONTROL_NRESET BIT(3) +#define CONTROL_UNKNOWN_24(x) (((x) & 3) << 24) +#define CONTROL_READY BIT(29) + +#define SPI_CONFIG_READ_MODE(x) (((x) & 3) << 2) +#define SPI_CONFIG_READ_CLKDIV(x) (((x) & 7) << 4) +#define SPI_CONFIG_READ_PACKET_SIZE(x) (((x) & 0x1ff) << 7) +#define SPI_CONFIG_WRITE_MODE(x) (((x) & 3) << 18) +#define SPI_CONFIG_WRITE_CLKDIV(x) (((x) & 7) << 20) +#define SPI_CONFIG_CLKDIV_8 BIT(23) // additionally divide clk by 8, for both read and write +#define SPI_CONFIG_WRITE_PACKET_SIZE(x) (((x) & 0xff) << 24) + +#define SPI_CLK_FREQ_BASE 125000000 +#define SPI_MODE_SINGLE 0 +#define SPI_MODE_DUAL 1 +#define SPI_MODE_QUAD 2 + +#define ERROR_CONTROL_UNKNOWN_0 BIT(0) +#define ERROR_CONTROL_DISABLE_DMA BIT(1) // clears DMA_RX_CONTROL_ENABLE when a DMA error occurs +#define ERROR_CONTROL_UNKNOWN_2 BIT(2) +#define ERROR_CONTROL_UNKNOWN_3 BIT(3) +#define ERROR_CONTROL_IRQ_DMA_UNKNOWN_9 BIT(9) +#define ERROR_CONTROL_IRQ_DMA_UNKNOWN_10 BIT(10) +#define ERROR_CONTROL_IRQ_DMA_UNKNOWN_12 BIT(12) +#define ERROR_CONTROL_IRQ_DMA_UNKNOWN_13 BIT(13) +#define ERROR_CONTROL_UNKNOWN_16(x) (((x) & 0xff) << 16) // spi error code irq? +#define ERROR_CONTROL_SET_DMA_STATUS BIT(29) // sets DMA_RX_STATUS_ERROR when a DMA error occurs + +#define ERROR_STATUS_DMA BIT(28) +#define ERROR_STATUS_SPI BIT(30) + +#define ERROR_FLAG_DMA_UNKNOWN_9 BIT(9) +#define ERROR_FLAG_DMA_UNKNOWN_10 BIT(10) +#define ERROR_FLAG_DMA_RX_TIMEOUT BIT(12) // set when we receive a truncated DMA message +#define ERROR_FLAG_DMA_UNKNOWN_13 BIT(13) +#define ERROR_FLAG_SPI_BUS_TURNAROUND BIT(16) +#define ERROR_FLAG_SPI_RESPONSE_TIMEOUT BIT(17) +#define ERROR_FLAG_SPI_INTRA_PACKET_TIMEOUT BIT(18) +#define ERROR_FLAG_SPI_INVALID_RESPONSE BIT(19) +#define ERROR_FLAG_SPI_HS_RX_TIMEOUT BIT(20) +#define ERROR_FLAG_SPI_TOUCH_IC_INIT BIT(21) + +#define SPI_CMD_CONTROL_SEND BIT(0) // cleared by device when sending is complete +#define SPI_CMD_CONTROL_IRQ BIT(1) + +#define SPI_CMD_CODE_READ 4 +#define SPI_CMD_CODE_WRITE 6 + +#define SPI_CMD_STATUS_DONE BIT(0) +#define SPI_CMD_STATUS_ERROR BIT(1) +#define SPI_CMD_STATUS_BUSY BIT(3) + +#define DMA_TX_CONTROL_SEND BIT(0) // cleared by device when sending is complete +#define DMA_TX_CONTROL_IRQ BIT(3) + +#define DMA_TX_STATUS_DONE BIT(0) +#define DMA_TX_STATUS_ERROR BIT(1) +#define DMA_TX_STATUS_UNKNOWN_2 BIT(2) +#define DMA_TX_STATUS_UNKNOWN_3 BIT(3) // busy? + +#define INPUT_HEADER_VERSION(x) ((x) & 0xf) +#define INPUT_HEADER_REPORT_LENGTH(x) (((x) >> 8) & 0x3fff) +#define INPUT_HEADER_SYNC(x) ((x) >> 24) +#define INPUT_HEADER_VERSION_VALUE 3 +#define INPUT_HEADER_SYNC_VALUE 0x5a + +#define QUICKSPI_CONFIG1_UNKNOWN_0(x) (((x) & 0x1f) << 0) +#define QUICKSPI_CONFIG1_UNKNOWN_5(x) (((x) & 0x1f) << 5) +#define QUICKSPI_CONFIG1_UNKNOWN_10(x) (((x) & 0x1f) << 10) +#define QUICKSPI_CONFIG1_UNKNOWN_16(x) (((x) & 0xffff) << 16) + +#define QUICKSPI_CONFIG2_UNKNOWN_0(x) (((x) & 0x1f) << 0) +#define QUICKSPI_CONFIG2_UNKNOWN_5(x) (((x) & 0x1f) << 5) +#define QUICKSPI_CONFIG2_UNKNOWN_12(x) (((x) & 0xf) << 12) +#define QUICKSPI_CONFIG2_UNKNOWN_16 BIT(16) +#define QUICKSPI_CONFIG2_UNKNOWN_17 BIT(17) +#define QUICKSPI_CONFIG2_DISABLE_READ_ADDRESS_INCREMENT BIT(24) +#define QUICKSPI_CONFIG2_DISABLE_WRITE_ADDRESS_INCREMENT BIT(25) +#define QUICKSPI_CONFIG2_ENABLE_WRITE_STREAMING_MODE BIT(27) +#define QUICKSPI_CONFIG2_IRQ_POLARITY BIT(28) + +#define DMA_RX_CONTROL_ENABLE BIT(0) +#define DMA_RX_CONTROL_IRQ_UNKNOWN_1 BIT(1) // rx1 only? +#define DMA_RX_CONTROL_IRQ_ERROR BIT(3) // rx1 only? +#define DMA_RX_CONTROL_IRQ_READY BIT(4) // rx0 only +#define DMA_RX_CONTROL_IRQ_DATA BIT(5) + +#define DMA_RX_CONTROL2_UNKNOWN_4 BIT(4) // rx1 only? +#define DMA_RX_CONTROL2_UNKNOWN_5 BIT(5) // rx0 only? +#define DMA_RX_CONTROL2_RESET BIT(7) // resets ringbuffer indices + +#define DMA_RX_WRAP_FLAG BIT(7) + +#define DMA_RX_STATUS_ERROR BIT(3) +#define DMA_RX_STATUS_READY BIT(4) // set in rx0 after using CONTROL_NRESET when it becomes possible to read config (can take >100ms) +#define DMA_RX_STATUS_HAVE_DATA BIT(5) +#define DMA_RX_STATUS_ENABLED BIT(8) + +#define INIT_UNKNOWN_GUC_2 BIT(2) +#define INIT_UNKNOWN_3 BIT(3) +#define INIT_UNKNOWN_GUC_4 BIT(4) +#define INIT_UNKNOWN_5 BIT(5) +#define INIT_UNKNOWN_31 BIT(31) + +// COUNTER_RESET can be written to counter registers to reset them to zero. However, in some cases this can mess up the THC. +#define COUNTER_RESET BIT(31) + +struct ithc_registers { + /* 0000 */ u32 _unknown_0000[5]; + /* 0014 */ u32 ltr_config; + /* 0018 */ u32 _unknown_0018[1018]; + /* 1000 */ u32 _unknown_1000; + /* 1004 */ u32 _unknown_1004; + /* 1008 */ u32 control_bits; + /* 100c */ u32 _unknown_100c; + /* 1010 */ u32 spi_config; + struct { + /* 1014/1018/101c */ u8 header; + /* 1015/1019/101d */ u8 quad; + /* 1016/101a/101e */ u8 dual; + /* 1017/101b/101f */ u8 single; + } opcode[3]; + /* 1020 */ u32 error_control; + /* 1024 */ u32 error_status; // write to clear + /* 1028 */ u32 error_flags; // write to clear + /* 102c */ u32 _unknown_102c[5]; + struct { + /* 1040 */ u8 control; + /* 1041 */ u8 code; + /* 1042 */ u16 size; + /* 1044 */ u32 status; // write to clear + /* 1048 */ u32 offset; + /* 104c */ u32 data[16]; + /* 108c */ u32 _unknown_108c; + } spi_cmd; + struct { + /* 1090 */ u64 addr; // cannot be written with writeq(), must use lo_hi_writeq() + /* 1098 */ u8 control; + /* 1099 */ u8 _unknown_1099; + /* 109a */ u8 _unknown_109a; + /* 109b */ u8 num_prds; + /* 109c */ u32 status; // write to clear + /* 10a0 */ u32 _unknown_10a0[5]; + /* 10b4 */ u32 spi_addr; + } dma_tx; + /* 10b8 */ u32 spi_header_addr; + union { + /* 10bc */ u32 irq_cause; // in legacy THC mode + /* 10bc */ u32 input_header; // in QuickSPI mode (see HIDSPI spec) + }; + /* 10c0 */ u32 _unknown_10c0[8]; + /* 10e0 */ u32 _unknown_10e0_counters[3]; + /* 10ec */ u32 quickspi_config1; + /* 10f0 */ u32 quickspi_config2; + /* 10f4 */ u32 _unknown_10f4[3]; + struct { + /* 1100/1200 */ u64 addr; // cannot be written with writeq(), must use lo_hi_writeq() + /* 1108/1208 */ u8 num_bufs; + /* 1109/1209 */ u8 num_prds; + /* 110a/120a */ u16 _unknown_110a; + /* 110c/120c */ u8 control; + /* 110d/120d */ u8 head; + /* 110e/120e */ u8 tail; + /* 110f/120f */ u8 control2; + /* 1110/1210 */ u32 status; // write to clear + /* 1114/1214 */ u32 _unknown_1114; + /* 1118/1218 */ u64 _unknown_1118_guc_addr; + /* 1120/1220 */ u32 _unknown_1120_guc; + /* 1124/1224 */ u32 _unknown_1124_guc; + /* 1128/1228 */ u32 init_unknown; + /* 112c/122c */ u32 _unknown_112c; + /* 1130/1230 */ u64 _unknown_1130_guc_addr; + /* 1138/1238 */ u32 _unknown_1138_guc; + /* 113c/123c */ u32 _unknown_113c; + /* 1140/1240 */ u32 _unknown_1140_guc; + /* 1144/1244 */ u32 _unknown_1144[11]; + /* 1170/1270 */ u32 spi_addr; + /* 1174/1274 */ u32 _unknown_1174[11]; + /* 11a0/12a0 */ u32 _unknown_11a0_counters[6]; + /* 11b8/12b8 */ u32 _unknown_11b8[18]; + } dma_rx[2]; +}; +static_assert(sizeof(struct ithc_registers) == 0x1300); + +void bitsl(__iomem u32 *reg, u32 mask, u32 val); +void bitsb(__iomem u8 *reg, u8 mask, u8 val); +#define bitsl_set(reg, x) bitsl(reg, x, x) +#define bitsb_set(reg, x) bitsb(reg, x, x) +int waitl(struct ithc *ithc, __iomem u32 *reg, u32 mask, u32 val); +int waitb(struct ithc *ithc, __iomem u8 *reg, u8 mask, u8 val); + +void ithc_set_ltr_config(struct ithc *ithc, u64 active_ltr_ns, u64 idle_ltr_ns); +void ithc_set_ltr_idle(struct ithc *ithc); +int ithc_set_spi_config(struct ithc *ithc, u8 clkdiv, bool clkdiv8, u8 read_mode, u8 write_mode); +int ithc_spi_command(struct ithc *ithc, u8 command, u32 offset, u32 size, void *data); + diff --git a/drivers/hid/ithc/ithc.h b/drivers/hid/ithc/ithc.h new file mode 100644 index 000000000000..aec320d4e945 --- /dev/null +++ b/drivers/hid/ithc/ithc.h @@ -0,0 +1,89 @@ +/* SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define DEVNAME "ithc" +#define DEVFULLNAME "Intel Touch Host Controller" + +#undef pr_fmt +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#define CHECK(fn, ...) ({ int r = fn(__VA_ARGS__); if (r < 0) pci_err(ithc->pci, "%s: %s failed with %i\n", __func__, #fn, r); r; }) +#define CHECK_RET(...) do { int r = CHECK(__VA_ARGS__); if (r < 0) return r; } while (0) + +#define NUM_RX_BUF 16 + +// PCI device IDs: +// Lakefield +#define PCI_DEVICE_ID_INTEL_THC_LKF_PORT1 0x98d0 +#define PCI_DEVICE_ID_INTEL_THC_LKF_PORT2 0x98d1 +// Tiger Lake +#define PCI_DEVICE_ID_INTEL_THC_TGL_LP_PORT1 0xa0d0 +#define PCI_DEVICE_ID_INTEL_THC_TGL_LP_PORT2 0xa0d1 +#define PCI_DEVICE_ID_INTEL_THC_TGL_H_PORT1 0x43d0 +#define PCI_DEVICE_ID_INTEL_THC_TGL_H_PORT2 0x43d1 +// Alder Lake +#define PCI_DEVICE_ID_INTEL_THC_ADL_S_PORT1 0x7ad8 +#define PCI_DEVICE_ID_INTEL_THC_ADL_S_PORT2 0x7ad9 +#define PCI_DEVICE_ID_INTEL_THC_ADL_P_PORT1 0x51d0 +#define PCI_DEVICE_ID_INTEL_THC_ADL_P_PORT2 0x51d1 +#define PCI_DEVICE_ID_INTEL_THC_ADL_M_PORT1 0x54d0 +#define PCI_DEVICE_ID_INTEL_THC_ADL_M_PORT2 0x54d1 +// Raptor Lake +#define PCI_DEVICE_ID_INTEL_THC_RPL_S_PORT1 0x7a58 +#define PCI_DEVICE_ID_INTEL_THC_RPL_S_PORT2 0x7a59 +// Meteor Lake +#define PCI_DEVICE_ID_INTEL_THC_MTL_S_PORT1 0x7f59 +#define PCI_DEVICE_ID_INTEL_THC_MTL_S_PORT2 0x7f5b +#define PCI_DEVICE_ID_INTEL_THC_MTL_MP_PORT1 0x7e49 +#define PCI_DEVICE_ID_INTEL_THC_MTL_MP_PORT2 0x7e4b + +struct ithc; + +#include "ithc-regs.h" +#include "ithc-hid.h" +#include "ithc-dma.h" +#include "ithc-legacy.h" +#include "ithc-quickspi.h" +#include "ithc-debug.h" + +struct ithc { + char phys[32]; + struct pci_dev *pci; + int irq; + struct task_struct *poll_thread; + struct timer_list idle_timer; + + struct ithc_registers __iomem *regs; + struct ithc_registers *prev_regs; // for debugging + struct ithc_dma_rx dma_rx[2]; + struct ithc_dma_tx dma_tx; + struct ithc_hid hid; + + bool use_quickspi; + bool have_config; + u16 vendor_id; + u16 product_id; + u32 product_rev; + u32 max_rx_size; + u32 max_tx_size; + u32 legacy_touch_cfg; +}; + +int ithc_reset(struct ithc *ithc); + -- 2.51.0